KlikkMedia | Google Hirdetés X Online Marketing Tanácsadás

Baldwin Boxall ROPSW Rack Option Panel Dual Paddle Switch

Baldwin Boxall ROPSW Rack Option Panel Dual Paddle SwitchThe ROPSW manufactured by Baldwin Boxall is a rack option paneldesigned with a dual paddle switch.

GBP 97.07

1

Baldwin Boxall VIGIL2 Power Supply with Dual Outputs BVSMP

Baldwin Boxall VIGIL2 Power Supply with Dual Outputs BVSMPVIGIL2 voice alarm system power supplies employ switch mode techniques to improve efficiency and reduce unwanted heat dissipation and weight.Key FeaturesThe BVSMP has two individually protected outputs at 24V the BVSMPLT has one.Each BVSMP will drive either two BV225 two BV125D or two BV050Q.Each BVSMPLT will drive one BV225 one BV125D or one BV050Q.Provide independent power converters with current and overvoltage protection circuits.Continual monitoring of the charger and all DC outputs ensures reliability.Standby batteries are continually float charged by the unit. Ensuring that in the event of mains failure power is maintained.Built-in deep battery discharge cut off preventing total discharge that can destroy the standby batteries in the event of AC power failure for long periods.A protected output is provided to power a mixer or auxiliary circuits.In the event of a fault condition an internal relay releases providing a changeover contact. A fault will be indicated on the EVAS router.The constant voltage charger is set for the recommended float charge. Should the battery fall below this level the BVSMP will charge at a constant rate of three Amps progressively reducing once the battery has achieved its nominal float level.Outputs together with a volt-free fault changeover contact are provided by a nine-way crimp connector plug and socket.Several chargers may be paralleled when used for larger systems. Paralleled BVSMPs must be synchronised.

GBP 1243.78

1

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075D

Baldwin Boxall VIGIL3 Dual 75W Class D Amplifier BV075DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV075D Dual 75W transformerless class D amplifier. Contains two independent 75W each amplifier has a single balanced line audio input and 75W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 1532.26

1

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300D

Baldwin Boxall VIGIL3 Dual 300W Class D Amplifier BV300DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV300D Dual 300W transformerless class D amplifier. Contains two independent 300W each amplifier has a single balanced line audio input and 300W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2413.15

1

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150D

Baldwin Boxall VIGIL3 Dual 150W Class D Amplifier BV150DThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV150D Contains two independent 150W each amplifier has a single balanced line audio input and 150W 100V line output. Can either be used as two independent amplifier modules or two amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 1787.18

1

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125D

Baldwin Boxall VIGIL2 Dual 125W Class D Amplifier BV125DThe BV125D Amplifier module contains two independent Class D Power amplifiers each with a single 500mV Balanced Line audio input and 125-Watt 100V Line output. The front panel status indicators show Power Overload and Output Level 10 and 100 output level for both amplifiers.The audio inputs to each amplifier are presented on separate RJ45 connectors. The outputs are presented on two 3-way plugcage clamp termination connectors providing 50V or 100V output. The 24V DC inputs are presented on two 2-way crimp connected sockets. The power output stages of the amplifiers are protected against overload conditions i.e. short circuits or abnormal loads.Should an amplifier be subjected to an abnormal load the input to the relevant power amplifier is attenuated to a safe level and the Overload LED will be illuminated. The amplifier output voltages are also sensed and should they exceed 100V the relevant input signal will be attenuated ensuring safe operation without creating unnecessary distortion.

GBP 1349.92

1

Baldwin Boxall VIGIL3 Battery Charger Module BVMBC

Baldwin Boxall VIGIL3 Battery Charger Module BVMBCVIGIL3 is our next generation of voice alarm system products. The charger module fits alongside the VIGIL3 amplifiers in a 2U mainframe. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.Key FeaturesThe VIGIL3 battery charger module BVMBC is compact it is actually half the size of the VIGIL2 power supply charger unit.The module continually monitors the system backup batteries and charges them whenever this is necessary.Neatly fits alongside the VIGIL3 amplifiers in a 2U mainframe.Only one charger module is required for up to five VIGIL3 amplifier modules.Continually monitors the power supplies in five VIGIL3 amplifier modules.The module features an auxiliary DC output which can be used for powering other equipment.For use with the new more powerful lighter weight VIGIL3 amplifiers Dual 75 Watt BVO75D Quad 75 Watt BVO75Q Dual 150 Watt BV150D Quad 150 Watt BV150Q Dual 300 Watt BV300D.The BVMBC when used with VIGIL3 amplifiers and the EVAS BVRD2M4 routers forms a complete EN54 compliant voice alarm system.

GBP 501.68

1

Baldwin Boxall DC Line Monitor BVRDADC

Baldwin Boxall DC Line Monitor BVRDADCThe Vigil BVRDADC is a loudspeaker line monitor and amplifier changeover unit for use with VIGIL amplifiers and the BVRD2M router. Each unit is supplied as a DIN rail-mounting module with screw terminals for connections to the amplifiers and loudspeaker lines. Connection to the BVRD2M is by CAN BUS ports. Each unit consists of ten channels that can be utilised for either dual or single circuit systems.For dual circuits ten working amplifiers five dual circuits and one standby amplifier can be accommodated. For single circuit systems ten working amplifiers ten single circuits and one standby amplifier are available. If an amplifier were to fail the BVRDADC automatically detects the faulty amplifier and switches over to a reserve amplifier until the fault has been rectified. A fault will be displayed on the BVRD2M front panel and also stored in the BVRD2M fault log.When the faulty amplifier has been replaced it is necessary to press the Fault Reset button on the front of the BVRD2M to restore the system and stop using the reserve amplifier. Each loudspeaker line including spurs must have an End of Line resistor fitted in parallel with the last physical loudspeaker on the line. All loudspeakers must be fitted with a DC Blocking capacitor. The BVRDADC monitors the integrity of the Loudspeaker Line by measuring a small DC current flowing through the End of Line resistors. Any change in this current indicates either a short circuit or open circuit condition on the loudspeaker line. Earth faults are also detected.

GBP 1449.71

1

Baldwin Boxall VIGIL2 EVAS Router with 4 Inputs and 4 Audio Outputs BVRD2M4

Baldwin Boxall VIGIL2 EVAS Router with 4 Inputs and 4 Audio Outputs BVRD2M4The BVRD2M4 is a four-zone voice alarm router with the same great features as the BVRD2M designed for smaller installations and networked decentralised systems.Key FeaturesDSP control.Possible to monitor up to four dual AB circuits.Four electronically balanced inputs. Input one is configurable with all call processor bypass and is normally used for the fire microphone in voice alarm systems. All inputs have both independent priority and level settings allowing for dual mode emergency and normal page.Up to fifteen priority levels are available. If two concurrent routes are set at the same priority they will be treated on a first come first served basis. Priorities are changeable.Three band parametric plus bass and treble equalisation on all inputs with limitercompressor enhancing the intelligibility of the system.Four audio electronically balanced 0dBM outputs with ten band parametric equalisation and audio delay of up to one second.Fully monitored surveillance at either 30Hz or 20kHz faults are recorded in the history log.Built-in real-time clock enables detailed logging and reporting including detected faults. Indicates time date month and year. Also used for night time volume reduction timed message trigger and to control external inputs. The history log can be accessed via the USB2 port on the front panel.Six flash stored 57 second messages with independent level surveillance and timing. Settings and messages are changeable password protected via the USB2 port.Nine selectable chimes pre-announcement tones of up to eight seconds in length.Up to 126 EVAS routers can be networked using fibre or copper to produce a truly sophisticated VA network.Message synchronisation even on a decentralised system.Ambient noise sensing using optional ambient noise sensing microphones.Amplifier changeover for up to three zones using optional relay board product code BVRD2M4ACO.Two RS485 ports for networking microphones etc.Zone grouping and barring on BVRD voice alarm controller.

GBP 1813.49

1

Baldwin Boxall BV3ADIS VIGIL 3 Slave DC Line Monitoring IsolatorChangeover Mod

Baldwin Boxall BV3ADIS VIGIL 3 Slave DC Line Monitoring IsolatorChangeover ModThe DC line monitor isolator units are CANBUS modules for the VIGIL voice alarm systems with VIGIL3 amplification consisting of two components BV3ADIM and BV3ADIS.Key FeaturesEnables dual loudspeaker circuits to connect to a single amplifierEach BV3ADIS unit provides both AB circuits for two amplifiersUp to 10 spurs per loudspeaker lineThe BV3ADIM master unit connects to a VIGIL3 amplifierUp to five BV3ADIS can be connected to one BV3ADIMFitting five BV3ADIS enables broadcast and monitoring for up to twenty loudspeaker circuitsThe modules plug directly togetherUtilises DC line monitoring techniques therefore BEL1 end of line monitoring is not required. Please refer to system requirements.Failure of either the A or B circuit from one amplifier will not effect the other circuitIn the event of an amplifier failure reserve amplifiers will automatically operateWith five BV3ADIS fitted a one-in-ten amplifier changeover ratio is enabledReduces rack size and cost for large voice alarm systemsEarth leakage detection

GBP 576.98

1

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075Q

Baldwin Boxall VIGIL3 Quad 75W Class D Amplifier BV075QThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV075Q Quad 75W transformerless class D amplifier. Contains four independent 75W each amplifier has a single balanced line audio input and 75W 100V line output. Can either be used as four independent amplifier modules or four amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2509.32

1

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150Q

Baldwin Boxall VIGIL3 Quad 150W Class D Amplifier BV150QThe VIGIL3 amplifiers form part of our new voice alarm range of products. They use new transformerless technology and have many great features. Our VIGIL3 range as with all of our products has been designed and built with quality and absolute reliability in mind.BV150Q Quad 150W transformerless class D amplifier. Contains four independent 150W each amplifier has a single balanced line audio input and 150W 100V line output. Can either be used as four independent amplifier modules or four amplifiers wired as an AB dual circuit using a single input signal.Key FeaturesNew floating transformerless technology which negates the need for cumbersome transformers. This means that Each amplifier is considerably lighter - weighing up to 58 less when compared on a Watt-for-Watt basis. Much less copper is required during manufacture.VIGIL3 amplifiers provide increased power in a smaller sized racksystem when compared to alternatives.With VIGIL3 amplifiers it is possible to fit up to 1800 Watts of power in one 2U rack space.Each amplifier unit includes a built-in power supply thus freeing up valuable rack space.The amplifiers have a sleep mode which Operates not only when the system is running on batteries but also when it is running on mains power. Will wake immediately when they are required - there is absolutely no down time. Will benefit users due to the reduction in mains power use - both financially and environmentally.Up to three amplifier units - providing up to 12 zones can be housed in a single 2U rack space.Being modular VIGIL3 amplifiers offer great flexibility for system design.Being backward compatible VIGIL3 amplifiers can replace VIGIL2 equivalents should this be required.VIGIL3 amplifiers when combined with the VIGIL3 battery charger module BVMBC and the BVRD2MBVRD2M4 VIGIL2 voice alarm routers form a powerful EN54 compliant voice alarm system VACIE.

GBP 2944.78

1

Baldwin Boxall Touch Screen Microphone BVRDTSM

Baldwin Boxall Touch Screen Microphone BVRDTSMIntroducing the new EN54 certified touch screen control microphone a multi-function user interface for VIGIL voice alarm systems.The BVRDTSM is an easy to use microphone with a touch sensitive screen that provides full control of the voice alarm system. Special features include a Near Field Communication NFC smart card user access facility.The microphone is a stylish unit which has all the functions that you would expect from a voice alarm system control microphone. It provides the user with unique options such as connecting a third-party music feed directly to the microphone to broadcast to selected areas or zones.The unit has a dual output ability which provides the opportunity to route a broadcast via an alternative rack on the system ideal for sites where separate A and B circuit racks are required. Another feature is the hard-wired bypass input which enables an emergency all call announcement in the unlikely event of a processor failure.With straight-forward multi-page scroll through operation the microphone enables full control of a VIGIL voice alarm system including access allowingZone or all call selection.Live speech for general paging announcements.Emergency paging facility given highest priority on the system automatically overriding all other broadcasts.Select system stored messages general and critical with priority given to the most critical for broadcast to chosen zones.Operators can use the microphone to record non-critical messages and store them for future use.A third-party music audio feed can be connected to the microphone. The output can then be routed by the user to a single or combination of zones.Select and route background music for broadcast to individual or multiple zones.Volume adjustment function provides the ability to change the volume of non-critical broadcasts to selected zones.View detailed activity history and fault logs.Configurable group buttons enable selection of multiple zones by a single touch.Configurable function buttons enable automatic multiple message playback.Key FeaturesStylish easy-to-use control microphone with a capacitive touch bright seven-inch screen.Emergency control mode live emergency broadcasts from the unit will override messages triggered by the fire panel.Near Field Communications NFC for card or pin based operator log-in feature enabling access to a pre-determined level of control.Dual output facility providing the ability to route the broadcast via a different rack on the system for sites where separate AB circuit racks are required.A hard-wired bypass input enables an emergency all call announcement in the unlikely event of a processor failure. There is also an option to fit an emergency bypass all call switch to the microphone.Critical signal path monitoring of the system - all faults being visibly and audibly indicated at the microphone.Compatible with VIGIL2 and VIGIL3 all microphone configuration is performed via the touch screen.

GBP 1654.73

1

Performance Marketing Agency

Gain the Advantage with KlikkMedia

Brand

Merchant

Price (EUR)