127 results (0,15916 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Solo 460 Heat Detector Tester Baffle for Fike Detectors 15-0239

Solo 460 Heat Detector Tester Baffle for Fike Detectors 15-0239

Solo 460 Heat Detector Tester Baffle for Fike Detectors 15-0239Due to the uniquely shaped detector chambers on Fike detectors the manufacturers developed a baffle to aid testing. the baffle is designed for the Solo 460 heat detector tester head unit and changes the direction of the direct heat flow to ensure a complete and effective test when testing Fike detectors. The baffle is inserted at the top of the Solo 460 as illustrated in the picture above.Please note Baffle only for use with Fike Detectors please remove when testing other detectors allowing for the direct heat flow to return to its standard format.

GBP 11.76
1

Fike Sita Loop Control Module 803-0022

Fike Sita Loop Control Module 803-0022

Fike Sita Loop Control Module 803-0022The Loop Monitored Output module provides an interface between ancillary devices and the loop. It can be configured as an output to control external devices or systems that require a 24VDC trigger that also monitors the cable condition between the module and device. Digital communication technology to the control panel is implemented allowing for accurate data transfer at high transmission speeds. This device includes a loop short-circuit isolator.Key FeaturesConnects to the addressable loopRequires a 24v DC EN54 PSU

GBP 87.74
1

Fike 505-0010 TwinflexPro2 Repeater Panel

Fike 505-0010 TwinflexPro2 Repeater Panel

Fike 505-0010 TwinflexPro2 Repeater PanelThe TWINFLEXpro2 repeater panel is smaller than the TWINFLEXpro2 control panel. It does not connect to or control detection devices. Instead it connects to a control panel and reports events which occur on the control panel. It can also perform system controls over the network i.e. Silence Alarms Reset Sound Alarms Silence Buzzer.A maximum of 8 repeater panels can be connected to a single control panel. The maximum cable length from the control panel to a repeater is 500 metres. If 8 repeaters are used they must all be within the maximum 500 metres cable length. All external connections are made on the back board. The Ext Switches on the back board are not currently used and are for a future development.Key FeaturesCompatible with all Twinflex Pro2 control panelsReports Twinflex Pro panel events to a remote locationCapable of performing system controls i.e. Silence Alarms Reset Sound Alarms Silence BuzzerMaximum of 8 repeater panels can be connected to a single control panelPlease Note The repeater will only work with the 4 8 Zone TwinflexPro2 panels using version 2.0 software.

GBP 183.98
1

Fike 600-0100 Anti-Fog Window for Head and Single Anti-Fog Reflector

Fike 600-0100 Anti-Fog Window for Head and Single Anti-Fog Reflector

Fike 600-0100 Anti-Fog Window for Head and Single Anti-Fog ReflectorThe Anti-Fog Kit consists of a retrofit lens that you attach to the front of the beam face and a single reflector. Both these items feature a special nano-coating that prevents condensation from forming. Condensation can be a problem in some unique environments where warm air meets a cold surface and the beams were unable to differentiate between this and smoke. Previously this would have resulted in a false alarm.Key FeaturesPrevents condensation

GBP 78.84
1

Fike TwinflexPro2 2 Wire 8 Zone Control Panel CPR Compliant - 505-0008

Fike TwinflexPro2 2 Wire 8 Zone Control Panel CPR Compliant - 505-0008

Fike TwinflexPro2 2 Wire 8 Zone Control Panel CPR Compliant - 505-0008The TwinflexPro2 panel is an intelligent 2-wire panel that utilises a conventional type cabling format. The system is classed as Analogue non-addressable due to the architecture used within the design. The devices communicate with the control panel using the Twinflex data protocol. The TwinflexPro2 panel is available in 24 8 zone variants which support up to 32 Twinflex devices per circuit. The TwinflexPro2 is able to recognise and separately identify between smoke detector heat detector and a manual call point alarm.The panel also monitors each zone for detector head removal device fault End of line fault and open or short circuit fault. The panel provides two monitored outputs that may be configured as conventional sounder circuits a volt free common fire relay and a volt free common fault relay. There are also two multifunction latchingnon-latching inputs and one monitored input programmable with options such as Class-Change and Remote fire. The control panel also incorporates an integral power supply unit and requires 2 x 12V 3.2Ah batteries to provide up to 72-hour standby times.The panel features a 500-event log daynight mode alarm confirmation and delay programming options that can be configured using the keypad or via PC driven OSP software. The TwinflexPro2 panel is no longer only compatible with Fikes Twinflex devices with the addition of our conventional zone card a 4 or 8 zone panel can now be configured to accept conventional devices on zones 5 to 8.Unlike most conventional fire alarm systems which require separate pairs of cables for detector zones and sounder circuits the Twinflex system requires one 2-core screened cable for each zone to accommodate both detection devices and sounders when using Twinflex devices.Key Features4 line x 20 character LCD displayAbility to differentiate between smoke detector heat detector or a manual call point alarmsAlarm confirmation featureAvailable in 2 4 and 8 zone panel versionsRS485 Connection to up to 8 Repeater panelsHighlighted selection menuEvent log storing up to 500 events3 enhanced test modesAllows detectors and sounders to be installed on the same pair of wiresUp to 32 devices per zoneBuilt-in EOL capability in all devices7 modes of detectionZone can be configured to daynight detection modeDelay programming optionsTwinflexPro2 ProtectsBed BreakfastsApartmentsFlatsHouses in Multiple Occupation HMORestaurantRetail StoresHistorical BuildingsMuseums Office Buildings

GBP 358.10
1

Fike TwinflexPro2 2 Wire 4 Zone Control Panel CPR Compliant - 505-0004

Fike TwinflexPro2 2 Wire 4 Zone Control Panel CPR Compliant - 505-0004

Fike TwinflexPro2 2 Wire 4 Zone Control Panel CPR Compliant - 505-0004The TwinflexPro2 panel is an intelligent 2-wire panel that utilises a conventional type cabling format. The system is classed as Analogue non-addressable due to the architecture used within the design. The devices communicate with the control panel using the Twinflex data protocol. The TwinflexPro2 panel is available in 24 8 zone variants which support up to 32 Twinflex devices per circuit. The TwinflexPro2 is able to recognise and separately identify between smoke detector heat detector and a manual call point alarm.The panel also monitors each zone for detector head removal device fault End of line fault and open or short circuit fault. The panel provides two monitored outputs that may be configured as conventional sounder circuits a volt free common fire relay and a volt free common fault relay. There are also two multifunction latchingnon-latching inputs and one monitored input programmable with options such as Class-Change and Remote fire. The control panel also incorporates an integral power supply unit and requires 2 x 12V 3.2Ah batteries to provide up to 72-hour standby times.The panel features a 500-event log daynight mode alarm confirmation and delay programming options that can be configured using the keypad or via PC driven OSP software. The TwinflexPro2 panel is no longer only compatible with Fikes Twinflex devices with the addition of our conventional zone card a 4 or 8 zone panel can now be configured to accept conventional devices on zones 5 to 8.Unlike most conventional fire alarm systems which require separate pairs of cables for detector zones and sounder circuits the Twinflex system requires one 2-core screened cable for each zone to accommodate both detection devices and sounders when using Twinflex devices.Key Features4 line x 20 character LCD displayAbility to differentiate between smoke detector heat detector or a manual call point alarmsAlarm confirmation featureAvailable in 2 4 and 8 zone panel versionsRS485 Connection to up to 8 Repeater panelsHighlighted selection menuEvent log storing up to 500 events3 enhanced test modesAllows detectors and sounders to be installed on the same pair of wiresUp to 32 devices per zoneBuilt-in EOL capability in all devices7 modes of detectionZone can be configured to daynight detection modeDelay programming optionsTwinflexPro2 ProtectsBed BreakfastsApartmentsFlatsHouses in Multiple Occupation HMORestaurantRetail StoresHistorical BuildingsMuseums Office Buildings

GBP 277.88
1

Fike 505-0002 TwinflexPro2 2 Wire 2 Zone Control Panel CPR Compliant

Fike 505-0002 TwinflexPro2 2 Wire 2 Zone Control Panel CPR Compliant

Fike 505-0002 TwinflexPro2 2 Wire 2 Zone Control Panel CPR CompliantThe TwinflexPro2 panel is an intelligent 2-wire panel that utilises a conventional type cabling format. The system is classed as Analogue non-addressable due to the architecture used within the design. The devices communicate with the control panel using the Twinflex data protocol. The TwinflexPro2 panel is available in 24 8 zone variants which support up to 32 Twinflex devices per circuit. The TwinflexPro2 is able to recognise and separately identify between smoke detector heat detector and a manual call point alarm.The panel also monitors each zone for detector head removal device fault End of line fault and open or short circuit fault. The panel provides two monitored outputs that may be configured as conventional sounder circuits a volt free common fire relay and a volt free common fault relay. There are also two multifunction latchingnon-latching inputs and one monitored input programmable with options such as Class-Change and Remote fire. The control panel also incorporates an integral power supply unit and requires 2 x 12V 3.2Ah batteries to provide up to 72-hour standby times.The panel features a 500-event log daynight mode alarm confirmation and delay programming options that can be configured using the keypad or via PC driven OSP software. The TwinflexPro2 panel is no longer only compatible with Fikes Twinflex devices with the addition of our conventional zone card a 4 or 8 zone panel can now be configured to accept conventional devices on zones 5 to 8.Unlike most conventional fire alarm systems which require separate pairs of cables for detector zones and sounder circuits the Twinflex system requires one 2-core screened cable for each zone to accommodate both detection devices and sounders when using Twinflex devices.Key Features4 line x 20 character LCD displayAbility to differentiate between smoke detector heat detector or a manual call point alarmsAlarm confirmation featureAvailable in 2 4 and 8 zone panel versionsRS485 Connection to up to 8 Repeater panelsHighlighted selection menuEvent log storing up to 500 events3 enhanced test modesAllows detectors and sounders to be installed on the same pair of wiresUp to 32 devices per zoneBuilt-in EOL capability in all devices7 modes of detectionZone can be configured to daynight detection modeDelay programming optionsTwinflexPro2 ProtectsBed BreakfastsApartmentsFlatsHouses in Multiple Occupation HMORestaurantRetail StoresHistorical BuildingsMuseums Office Buildings

GBP 230.99
1

Fike FIK-FSIM-UV-IR-KIT Flame Simulator Kit UV-IR

Fike FIK-FSIM-UV-IR-KIT Flame Simulator Kit UV-IR

Fike FIK-FSIM-UV-IR-KIT Flame Simulator Kit UV-IRThis simulator kit includes a flame simulator for the UV-IR flame detector aluminium a simulator carrying case and strap a cover tool and a charger. The UV-IR monitor detects a large variety of fires including hydrocarbon fires visible and non-visible and Hydrogen fires.These Flame Simulators are designed to test flame detectors and ensure they are performing accurately and adequately. The flame simulators are economic and ideal for ongoing maintenance. They are lightweight and very easy to use. They can be used in a hazardous area and can test in distances of up to 23 feet away from the detectors reducing the need for scaffolding.They are ideal for applications where commissioning and periodic system testing is required for the detectors. There are other versions available. Please refer to the datasheet for additional information on detector sensitivities operational distances and electrical specifications.Key FeaturesMore than 1000 activations between charges so uptime is highPerforms automatic self-tests of optics windows electronics and softwareCan be manually put into alarm through FGD communicator software or by short-circuiting the Manual BIT terminal24 VDC terminal for one secondDesigned to complement inbuilt features by providing a full external loop test capability

GBP 4931.93
1

Fike 403-0006-NC Sita Manual Call Point - No Cover

Fike 403-0006-NC Sita Manual Call Point - No Cover

Fike 403-0006-NC Sita Manual Call Point - No CoverAn addressable Manual Call point with re-settable element reset key back box adaptor plate for flush mounting and inbuilt short circuit isolator.The Sita Manual Call Point allows for user activation of the fire alarm system. Once operated the device latches into the alarm position and requires manually resetting via a special key. The MCP is an addressable unit that attaches to the loop. Digital communication technology to the control panel is implemented allowing for accurate data transfer at high transmission speeds. This device is only compatible with the Sita200plus Duonet and Quadnet ranges of control panel.Key FeaturesRe-settable elementReset keyBack boxAdaptor plate for flush mountingInbuilt short circuit isolatorNo cover

GBP 34.62
1