40 results (0,16181 seconds)

Show all filters

Brand

Colour

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Mini Salt and Grit Bin Yellow 50L - 389110

Mini Salt and Grit Bin Yellow 50L - 389110

Mini Salt and Grit Bin is a compact design that holds up to 50kg of salt. It has a wide mouth for easy access. Manufactured from UV resistant polyethylene. With 50 Litre capacity. Stackable when empty for storage over summer. Mini Salt and Grit Bin Yellow 50L Compact design holds up to 50kg of salt Wide mouth for easy access Manufactured from UV resistant polyethylene Capacity: 50 Litre Stackable when empty for storage over summer Dimensions (HxWxD) : 450x590x420mm Salt available to purchase separately

GBP 99.99
1

Mini Salt and Grit Bin with Locking Lid Yellow 50L - 389111

Mini Salt and Grit Bin with Locking Lid Yellow 50L - 389111

Mini Salt and Grit Bin with Locking Lid and with a hasp for padlock (padlock not supplied) The compact design holds up to 50kg of salt. It has a wide mouth for easy access. Manufactured from UV resistant polyethylene. With a 50 Litre capacity. Stackable when empty for storage over summer. Mini Salt and Grit Bin with Locking Lid Locking lid with hasp for padlock (padlock not supplied) Compact design holds up to 50kg of salt Wide mouth for easy access Manufactured from UV resistant polyethylene Capacity: 50 Litre Stackable when empty for storage over summer Dimensions (HxWxD) : 450x590x420mm Salt available to purchase separately

GBP 109.99
1

M14X2.00MM Chaser Die 20M M D/HD Type S20

M14X2.00MM Chaser Die 20M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 123.99
1

3/4" BSW Chaser Die 20MMD/HD Type S20

3/4" BSW Chaser Die 20MMD/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 119.99
1

M20X2.50MM Chaser Die 20M M D/HD Type S20

M20X2.50MM Chaser Die 20M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 123.99
1

1" BSP Chaser Die 25MM D/HD Type S20

1" BSP Chaser Die 25MM D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 133.99
1

M20X2.50MM Chaser Die 25M M D/HD Type S20

M20X2.50MM Chaser Die 25M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 149.99
1

M12X1.75MM Chaser Die 20M M D/HD Type S20

M12X1.75MM Chaser Die 20M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 123.99
1

3/4" BSP Chaser Die 25MMD/HD Type S20

3/4" BSP Chaser Die 25MMD/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with: diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 133.99
1

M8X1.25MM Chaser Die 12MM D/HD Type S20

M8X1.25MM Chaser Die 12MM D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 99.99
1

M10X1.50MM Chaser Die 20M M D/HD Type S20

M10X1.50MM Chaser Die 20M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 123.99
1

M5X0.80MM Chaser Die 12MM D/HD Type S20

M5X0.80MM Chaser Die 12MM D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 99.99
1

M4X0.70MM Chaser Die 12MM D/HD Type S20

M4X0.70MM Chaser Die 12MM D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 99.99
1

M24X3.00MM Chaser Die 25M M D/HD Type S20

M24X3.00MM Chaser Die 25M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 149.99
1