5 results (0,13403 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

GF30 One Way Battery Operated Controller

GF30 One Way Battery Operated Controller

Simple, intuitive and practical, the GF30 Electronic Programmer has programs that can be combined with each other up to 30 possibilities, manageable through the two easy-to-use rotary switches. Ideal for outdoor use, it is supplied with a device to stop the flow of water in case of battery exhaustion, while its electrical components are protected from water and humidity. Technical specifications GF30 one way battery operated programmer GF30 One-Way Battery Programmer Automatic start: every 3, 6, 12, 24, 48 hours for 1, 3, 5, 15, 30, 60 minutes Manual start: with dedicated button Delayed start: of 8 hours (dedicated key) Battery: 9 volt alkaline Connection: to the tap, 3/4" Maximum working pressure of the GF30 programmer: 8 bar Click to download:  Technical data sheet for GF30 one-way battery operated programmer

GBP 98.16
1

GF2Way 2 Way Battery Operated Controller

GF2Way 2 Way Battery Operated Controller

Installing the GF2Way 2-Way Battery Programmer: 1) Open the battery compartment and insert a new 9V alkaline battery. 2) While holding the GF2Way programmer, screw the locking collar onto the faucet until fully tightened, tightening it well. Then open the faucet. Do not use wrenches or pliers to tighten the collar. 3) Turn the RUN TIME knob and set the duration for ZONE 1 adjustment. 4) Turn the FREQUENCY knob (ZONE 1) to the RESET position. The red light flashes. 5) Then set the FREQUENCY TIME of the GF2Way battery-operated 2-way programmer. 6) Perform the previous steps again for ZONE 2. 7) If the red light does not flash: check the battery and make sure it is installed correctly. 8) Note the date and time of the adjustment, the frequency (FREQUENCY) and the duration (RUN TIME) for future reference. 9) It is possible at any time to operate the manual ON/OFF function of the GF2Way programmer: a) By turning the knob to ON, the valve opens for 30 minutes, then automatically turns off b) If you want to stop watering before 30 minutes, turn the knob to the OFF position. c) At the end of the manual watering time, remember to reset the duration (RUN TIME) to the original control time as per step #3, otherwise the old settings will be lost Technical specifications 2-Way Battery Operated Programmer GF2Way GF2Way Programmer Min. operating pressure: 0.5 bar Max. operating pressure: 8 bar Max. water temperature: 40° C

GBP 167.52
1

RPE Solenoid Valve with Reinforcement 9/12V

RPE Solenoid Valve with Reinforcement 9/12V

Solenoid Valve Body RPE 9/12V: Polyamide, 30% fiberglass Diaphragm: NBR (buna) Operating Pressure: 0.5 - 10 bar Fluid Temperature: Tm 60ºC Solenoid/Control: Normally Closed/Voltage 9/12Volt Designed for irrigation systems with metal manifolds and branches, this series features brass threads molded into inlet and outlet. Solenoid valve suitable for irrigation only, its operation allows to receive impulse from battery operated controller.

GBP 106.80
1

RPE Solenoid Valve 3/4" with Bistable Reinforcement 9/12V

RPE Solenoid Valve 3/4" with Bistable Reinforcement 9/12V

Body: Polyamide, 30% fiberglass Diaphragm: NBR (buna) Operating Pressure: 0.5 - 10 bar Fluid Temperature: Tm 60°C Solenoid/Control: Normally Closed/Voltage 9/12Volt Belonging to the series with brass inlet and outlet co-molded threads, the3/4" Solenoid Valve with 9/12V reinforcement is designed for irrigation systems where manifolds and branches are made of metal. Solenoid valve suitable only for irrigation, its operation allows to receive impulse from battery programmer.

GBP 102.00
1