31 results (0,15139 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Advanced Sounder Splitter Card - MXS-021

Advanced Sounder Splitter Card - MXS-021

Advanced Sounder Splitter Card - MXS-021The Mxs-021 Sounder Circuit Splitter is a peripheral unit for use with all MxPro4 range of control Panels. This additional unit takes a standard sounder circuit from either a control panel or other panel based sounder circuit controller and multiplies to provide up to 4 monitored outputs. In operation the additional outputs follow the output they are connected to. The circuits are fully monitored for open and short circuit and will take an independent supply to provide up to 1A per circuit.Key Features4 Monitored Outputs3 Year Warranty as standardUp to 1 Amp per circuitCost effective against ancillary hardwareCompatibilityThe Sounder Splitter Cardis compatible with all MxPro 4 controlpanels.LimitationsThe 4-way sounder splitter card can be supplied as a PCB only for mounting. When supplied fitted in this format the load at the outputs from the splitter will be limited to the sounder output loading of the input circuit from which it is driven.All 4 outputs on the sounder splitter card will operate in tandem and follow the output of the sounder circuit to which the card is connected.

GBP 163.18
1

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052The Mxp-052 is a peripheral relay card providing ten 30V DC 1A programmable relay outputs. The Mxp-052 connects directly to any of the DIL connectors of either the Network Mimic Mxp-020-100 LED Output Card or the General IO controller Mxp-045 LED Output Card units via the supplied ribbon cable.Each output follows the cause and effect programming of the mimic unit output. This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the Mx-40005000 systems Dynamix zoning facilities.Key FeaturesTen change-over contact outputs rated at 30V DC 1A.Up to 200 individual relay outputs fully programmable per mimic excluding LEDsTen individually programmable relay outputs per unitDIN rail or screw fixing optionsSeparate isolate input disables all outputsSeparate isolate indication outputFast instant responseProduct CodesDescriptionMXP-052Mimic driven 10-way relay output cardMXP-052-DINMimic driven 10-way relay output card in din-rail carrier

GBP 129.16
1

Advanced Latch Stretch Input Card - MXP-053

Advanced Latch Stretch Input Card - MXP-053

Advanced Latch Stretch Input Card - Mxp-053The Mxp-053 Input Latch Stretch Module will provide monitoring for two momentary switch inputs. The module can be configured for Latch or Stretch Modes of operation. The module can be configured for wiring supervision using the End-of-Line resistor of the host input device. A reset input is provided for the reset of a latched condition.Can be used to monitor the operation of a momentary switched input that has been interfaced to the fire alarm control panel via loop devices or onboard inputs. Two modes of operation are available for momentary switched operation Latched or Stretched 30 Seconds. Can be powered by a separate 24V DC supply or loop powered.Key FeaturesTwo modes of operation - Latched or Stretched Monitored or Non-monitored connectivityLoop powered Configurable for Advanced Apollo Hochiki and Nittan input circuitsThe module can be loop powered3-year warranty as standard

GBP 115.84
1

Advanced ExGo 2 Way Relay Output Card - EXP-007

Advanced ExGo 2 Way Relay Output Card - EXP-007

Advanced ExGo 2 Way Relay Output Card - EXP-007The 2 or 8 Way Relay Output Card is an internal peripheral for use with The ExGo series control panels and status indicators. This additional PCB provides a cost effective solution to providing 2 or 8 individually programmable 1 Amp rated volt free clean contact outputs. The 2 or 8 Way Relay Output Card connects directly to the panels motherboard in which each output can be individually programmed. Ideal for any application where a number of programmable outputs are required at the panel. The features of the 2 or 8 Way Relay Output Card not only aid commissioning and cut down on expensive ancillary hardware but also allow the system to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key Features2 Individual Programmable OutputsFast Instant ResponseEach Output 30V ACDC 1 Amp RatingCost effective against ancillary hardware

GBP 120.76
1

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail Carrier

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail Carrier

Advanced MXP-052-DIN Mimic Driven 10-Way Relay Output Card in Din-Rail CarrierThe Peripheral Relay Card provides 10 30V DC 1A programmable relay outputs.The Peripheral Relay Card connects directly to any of the DIL connectors of either the Network Mimic 100 LED Output Card or the Multi way InputOutput Card unit via the supplied ribbon cable.Each output follows the cause-and-effect programming of the mimic unit output.This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the MxPro5 Dynamic zoning facilities.Key FeaturesTen change-over contacts outputs at 30Vdc 1ADIN rail fixingSeparate isolate input disables all outputsSeparate isolate indication outputFast response

GBP 149.43
1

Advanced Sounder Booster Card - MXS-025

Advanced Sounder Booster Card - MXS-025

Advanced Sounder Booster Card MXS-025The Sounder Booster Card is a peripheral unit that utilises a standard sounder circuit panel or loop driven and provides increased sounder output capability.This boosted output is fully monitored for open and short circuits and will take an independent supply to provide up to 4A of sounder current to a single circuit.On-board indication via 2 LED indicators located on the booster PCB enable the user to view when an output has been triggered and when an external power supply has been connected.Applications LimitationsThe sounder booster is used where a single sounder output circuit of up to 4A is required.Each of the panels sounder outputs can only monitor a single circuit. The unit must therefore be situated at the end of the panels sounder output circuit to maintain correct fault monitoring.Key FeaturesIncreased sounder capability up to 4AOn-board indicationPSU fault input contactsCost effective against ancillary hardware3 year warranty as standardCompatibilityThe Sounder Booster Cardis compatible with allMxPro 5controlpanels.

GBP 122.83
1

Advanced MXP-507 2-Way Relay Card MxPro 5

Advanced MXP-507 2-Way Relay Card MxPro 5

Advanced MXP-507 2-Way Relay Card MxPro 5The 2-Way Programmable Relay Card2-Way Relay Output Card is an internal peripheral for use with MxPro 5 series control panels.This additional PCB provides a cost-effective solution to providing 2 individually programmable 1 Amp rated volt free change over contacts.The 2-Way Programmable Relay Cardconnects directly to the panels motherboard in which each output can be individually assigned to an output group to provide full support for dynamic zoning.ApplicationsIdeal for any application where a number of programmable outputs are required at the panel e.g. landlordtenant interfaces.The system can to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key FeaturesEach output individually programmableOptional fail-safe setupAllow investigation delaysCan silence optionInstant response timeCost effective against ancillary hardwareEach output 30V ACDC 1 Amp rating3 year warranty as standard

GBP 118.54
1

Advanced MxPro 5 MXP-507F 2-Way Relay Card Fitted

Advanced MxPro 5 MXP-507F 2-Way Relay Card Fitted

Advanced MxPro 5 MXP-507F 2-Way Relay Card FittedThe 2-Way Programmable Relay Card2-Way Relay Output Card is an internal peripheral for use with MxPro 5 series control panels.This additional PCB provides a cost-effective solution to providing 2 individually programmable 1 Amp rated volt free change over contacts.The 2-Way Programmable Relay Cardconnects directly to the panels motherboard in which each output can be individually assigned to an output group to provide full support for dynamic zoning.ApplicationsIdeal for any application where a number of programmable outputs are required at the panel e.g. landlordtenant interfaces.The system can to be easily configured to provide additional outputs for the more complex cause and effect configurations using standard products.Key FeaturesEach output individually programmableOptional fail-safe setupAllow investigation delaysCan silence optionInstant response timeCost effective against ancillary hardwareEach output 30V ACDC 1 Amp rating3-year warranty as standard

GBP 118.54
1

Advanced MxPro 5 MXP-511F Access Enable Key Switch Fitted

Advanced MxPro 5 MXP-511F Access Enable Key Switch Fitted

Advanced MxPro 5 MXP-511F Access Enable Key Switch FittedTheMxPro 5control panel range supportsdirect installation of up to 8 individual key switches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.CompatibilityCan be used with allMxPro 5series control panels.LimitationsIf an on-board printer is fitted to the MxPro 5 2 4 loop control panels then the maximum number of switches fitted is limited to 4. If the MxPro 5 3 position switch is fitted then two programmable inputs must be available per switch.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switches

GBP 98.59
1

Advanced MxPro 5 MXP-519F 2-Pos Key Switch - Mom Trapped Fitted

Advanced MxPro 5 MXP-519F 2-Pos Key Switch - Mom Trapped Fitted

Advanced MxPro 5 MXP-519F 2-Pos Key Switch - Mom Trapped FittedTheMxPro 5control panel range supportsdirect installation of up to 8 individual key switches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switches

GBP 98.59
1

Advanced MxPro 5 MXP-515F 3-Position Key Switch - Trapped Requires 2 Inputs

Advanced MxPro 5 MXP-515F 3-Position Key Switch - Trapped Requires 2 Inputs

Advanced MxPro 5 MXP-515F 3-Position Key Switch - Trapped Requires 2 InputsThe MxPro 5control panel range supportsdirect installation of up to 8 individual key switches.ApplicationsThe MxPro 5 1 loop permits 1 key-switch to be fitted but the MxPro 5 2 4 loop control panels allow a maximum of 8.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switches

GBP 98.59
1

Advanced ExGo EXP-004-065 Abort Switch - IP65 Plastic Enclosure

Advanced ExGo EXP-004-065 Abort Switch - IP65 Plastic Enclosure

Advanced ExGo EXP-004-065 Abort Switch IP65 Plastic EnclosureThe Hold and Abort Switch Modules complement the ExGo extinguishing and suppression control panels.The modules comply with the requirementsof BS7273-1.The switches are easy to wire and multiple units can easily be daisy-chained together on an input circuit.A range of finishes are available - white stainless steel and brass trims.Alternatively the unit can be supplied in an IP65 rated enclosure.The standard units can be surface mounted or semi-flush mounted onto standard 3 electrical boxes. The IP65 unit is surface mounted.All units are provided with an end of line resistor Reol.Compatible with the ExGo gas extinguishing panel and remote status indicator panel input circuits.Key FeaturesRange of finishes availableSurface or flush mountIP65 optionComplies with BS7273-1 requirementsStandard units available in white plastic finish

GBP 109.73
1

Advanced ExGo EXP-003-065 Hold Switch IP65 Plastic Enclosure

Advanced ExGo EXP-003-065 Hold Switch IP65 Plastic Enclosure

Advanced ExGo EXP-003-065 Hold Switch IP65 Plastic EnclosureThe Hold and Abort Switch Modules compliment the ExGo extinguishing and suppression control panels.The modules comply with the requirementsof BS7273-1.The switches are easy to wire and multiple units can easily be daisy-chained together on an input circuit.A range of finishes are available - white stainless steel and brass trims.Alternatively the unit can be supplied in an IP65 rated enclosure.The standard units can be surface mounted or semi-flush mounted onto standard 3 electrical boxes. The IP65 unit is surface mounted.All units are provided with an end of line resistor Reol.Compatible with the ExGo gas extinguishing panel and remote status indicator panel input circuits.Key FeaturesRange of finishes availableSurface or flush mountIP65 optionComplies with BS7273-1 requirementsStandard units available in white plastic finish

GBP 109.73
1

Advanced ExGo EXP-003-003 Hold Switch Brass Trim Cover Plate

Advanced ExGo EXP-003-003 Hold Switch Brass Trim Cover Plate

Advanced ExGo EXP-003-003 Hold Switch Brass Trim Cover PlateThe Hold and Abort Switch Modules compliment the ExGo extinguishing and suppression control panels.The modules comply with the requirementsof BS7273-1.The switches are easy to wire and multiple units can easily be daisy-chained together on an input circuit.A range of finishes are available - white stainless steel and brass trims.Alternatively the unit can be supplied in an IP65 rated enclosure.The standard units can be surface mounted or semi-flush mounted onto standard 3 electrical boxes. The IP65 unit is surface mounted.All units are provided with an end of line resistor Reol.Compatible with the ExGo gas extinguishing panel and remote status indicator panel input circuits.Key FeaturesRange of finishes availableSurface or flush mountIP65 optionComplies with BS7273-1 requirementsStandard units available in white plastic finish

GBP 105.14
1

Advanced MxPro5 MXP-515TF 3-Pos Key Switch Key-free in centre position only Fitted

Advanced MxPro5 MXP-515TF 3-Pos Key Switch Key-free in centre position only Fitted

Advanced MxPro5 MXP-515TF 3 -Pos Key Switch Key-free in centre position only FittedThe MxPro5 control panel range supports direct installation of up to 8 individual key switches.ApplicationsThe MxPro5 1 loop permits 1 key-switch to be fitted but the MxPro5 2 4 loop control panels allow a maximum of 8.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-Trapped key switchesCan be used with all MxPro5 series control panels

GBP 98.59
1

Advanced MxPro 5 MXP-517F 2-Pos Key Switch Untrapped Fitted

Advanced MxPro 5 MXP-517F 2-Pos Key Switch Untrapped Fitted

Advanced MxPro 5 MXP-517F 2-Pos Key Switch Untrapped FittedThe MxPro 5control panel range supportsdirect installation of up to 8 individual key switches.Key FeaturesEnabledisable controlsGroup isolate to disable IO across networkFor use to startenable a class changeTrapped and un-trapped key switches availableControl of multi-sensordevice sensitivity mode changeSimple to install and configureTrapped and Un-trapped key switches

GBP 98.59
1

Advanced ExGo Abort Switch Brass Trim Cover Plate EXP-004-003

Advanced ExGo Abort Switch Brass Trim Cover Plate EXP-004-003

Advanced ExGo Abort Switch Brass Trim Cover Plate EXP-004-003The Hold and Abort Switch Modules compliment the ExGo extinguishing and suppression control panels. The modules comply with the requirementsof BS7273-1.The switches are easy to wire and multiple units can easily be daisy-chained together on an input circuit.A range of finishes are available - white stainless steel and brass trims.Alternatively the unit can be supplied in an IP65 rated enclosure. The standard units can be surface mounted or semi-flush mounted onto standard 3 electrical boxes.The IP65 unit is surface mounted. All units are provided with an end of line resistor Roel. Compatible with the ExGo gas extinguishing panel and remote status indicator panel input circuits.Key FeaturesRange of finishes availableSurface or flush mountIP65 optionComplies with BS7273-1 requirementsStandard units available in white plastic finish

GBP 105.14
1

Advanced ExGo EXP-003-002 Hold Switch Stainless Steel Trim Cover Plate

Advanced ExGo EXP-003-002 Hold Switch Stainless Steel Trim Cover Plate

Advanced ExGo EXP-003-002 Hold Switch Stainless Steel Trim Cover PlateThe Hold and Abort Switch Modules compliment the ExGo extinguishing and suppression control panels.The modules comply with the requirementsof BS7273-1.The switches are easy to wire and multiple units can easily be daisy-chained together on an input circuit.A range of finishes are available - white stainless steel and brass trims.Alternatively the unit can be supplied in an IP65 rated enclosure.The standard units can be surface mounted or semi-flush mounted onto standard 3 electrical boxes. The IP65 unit is surface mounted.All units are provided with an end of line resistor Reol.Compatible with the ExGo gas extinguishing panel and remote status indicator panel input circuits.Key FeaturesRange of finishes availableSurface or flush mountIP65 optionComplies with BS7273-1 requirementsStandard units available in white plastic finish

GBP 105.14
1