609 results (0,14256 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec EVC301JP Single Gang Jack Plate

C-Tec EVC301JP Single Gang Jack Plate

C-Tec EVC301JP Single Gang Jack PlateA single gang jack plate designed for use in conjunction with an EVC401JPH portable fire telephone handset on compatible SigTEL emergency voice communication systems. When the handset not supplied is plugged into the Jack Plate it will call theSigTEL master controller from where a two-way speech channel can be opened and instructions communicated.Key FeaturesCan be mounted on 25mm UK flush or surface single gang back box.Multiple jack plates can be connected to a single SigTEL Master Controllerline in stairwells etc.Designed for use in regions where roaming handsets are accepted typically the Far and Middle East. UK standard BS5839-9 DOES NOTallow the use ofthese devices.Facilitatesreliable two-way communication in anemergency between a permanently manned control room and key points ofasite.

GBP 29.30
1

C-Tec BF364 Single Gang Locking Jack Socket

C-Tec BF364 Single Gang Locking Jack Socket

Please note that this product is now obsolete. The replacement isC-Tec BF320JP XLR Connector Plate for BF320C-Tec BF364 Single Gang Locking Jack Socket for use with BF363The BF364 allows the BF363 Vibrating Pillow Pad to be connected to a 24V DC conventional fire alarm sounder circuit. The BF364 typically used to provide early warning of a potential fire alarm condition to the hard of hearing.Key FeaturesMax operating voltage 27V DCMounts on a standard UK 18mm single gang flush or surface back boxIncludes Braille text

GBP 37.43
1

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm

C-Tec APQM Microphone Jack Plate 6.35mm The Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier.Each input plate features a built-in mixer preamp input level control and balanced output. Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723.Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c.. Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts balanced or unbalanced electret microphones with 6.35mm 14 jack plugs.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mm

C-Tec APQL Line Level Jack Plate 6.35mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-TECs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts 6.35mm 14 jack feeds from audio equipment such as stage or church mixing desks etc.Part of C-TECs patented Outreach Plate audio input extension system.Compatible with C-TECs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 49.57
1

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mm

C-Tec APJ Microphone Jack Outreach Plate 3.5mmThe Outreach Plate audio input extension system comprises a range of wall ceiling and desk mountable plates specifically designed to increase the audio input capability of any audio system. Covering the most common variants of audio connectors they work by mixing the signals from various audio input sources into a single balanced line level input on a compatible amplifier. Each input plate features a built-in mixer preamp input level control and balanced output.Typically up to 10Outreach plates any mix can be daisy-chained to one balanced line level connection with cable lengths up to 100m easily achievable using standard two-pair audio cable i.e. Belden 8723. Each plate requires four wires two balanced line LineA LineA one ground GND and one power connection V 12-32V d.c..Most of C-Tecs PDA Range induction loop amplifiers are fitted with an Outreach connection socket as standard. For audio systems that do not have an Outreach socket straightforward network connection can be achieved using an APV 24V 250mA d.c. regulated power supply and an APXO 3 pin XLR balanced line output plate.Key FeaturesAccepts unbalanced electret microphones with 3.5mm mono jack plugs.Part of C-Tecs patented Outreach Plate audio input extension system.Compatible with C-Tecs entire range of PDA102 200E Pro-Rangeand ML1 induction loop amplifiers.Can be connected to any third-party audio or induction loop amplifier using an APV 24V 250mA power supply.Mounts on a 25mm standard UK single gang back box.

GBP 47.59
1

C-Tec EVC401PH Roaming Fire Telephone Handset

C-Tec EVC401PH Roaming Fire Telephone Handset

C-Tec EVC401PH Roaming Fire Telephone HandsetA portable fire telephone handset designed for usein conjunction with a series of EVC301JP Jack Plates on compatible SigTEL emergency voice communication systems. Whenplugged intoan EVC301JP Jack Plate not supplied the handset will call theSigTEL master controller from where a two-way speech channel can be opened and instructions communicated.Key FeaturesIncludes a flexible 1.5m coiled lead cw a 14 jack plug.Multiple jack plates can be connected to a single SigTEL Master Controllerline in stairwells etc.Designed for use in regions where roaming handsets are accepted typically the Far and Middle East. UK standard BS5839-9 DOES NOTallow the use ofthese devices.Facilitatesreliable two-way communication in anemergency between a permanently manned control room and key points ofasite.

GBP 109.87
1

C-Tec QT635 Enuresis Bed Wet Sensor

C-Tec QT635 Enuresis Bed Wet Sensor

C-Tec QT635 Enuresis Bed Wet SensorDesigned to trigger a call when moisture is detected in a patients bed. Connects to Quantec via the jack socket on the QT637 Enuresisgeneral purpose interface socket. Typically positioned across and over amattress directly underneath the bed sheet.Key FeaturesProtects against patient discomfort and reduces the number of incontinence checks staff are required to make.Measures 80cm x 12cm and is supplied with a 2m lead and normally open right angled jack plug.Wipe clean design - can be re-used many times.

GBP 34.24
1

C-Tec QT634 Chair Exit Mat

C-Tec QT634 Chair Exit Mat

C-Tec QT634 Chair Exit MatDesigned to trigger a call by sensing the pressure change when a patient exits a chair. Connects to Quantec via the remote jack socket on a QT637 EnuresisGeneral Purpose Interface Socket or QT636 Interface Unit. To reduce the risk of nuisance calls the QT637 includes circuitry that prevents a momentary change in pressure such as a patient quickly changing position from triggering a call. Measures 400mm x 250mmand is supplied with a 2m lead and normally closed right angled jack plug.

GBP 36.64
1

C-Tec QT633 Bed Exit Mat

C-Tec QT633 Bed Exit Mat

C-Tec QT633 Bed Exit MatDesigned to trigger a call by sensing the pressure change when a patient exits a bed. Connects to Quantec via the remote jack socket on a QT637 EnuresisGeneral Purpose Interface Socket or QT636 Interface Unit. To reduce the risk of nuisance calls the QT637 includes circuitry that prevents a momentary change in pressure such as a patient quickly changing position from triggering a call.Key FeaturesTypically positioned across and overamattress directly underneath the bedsheet.Measures 80cm x 10cm and is supplied with a 2m lead and normally closed right angled jack plug.

GBP 34.70
1

C-Tec BF320JP XLR Connector Plate for BF320

C-Tec BF320JP XLR Connector Plate for BF320

C-Tec BF320JP XLR Connector Plate for BF320The BF320JP can be used in conjunction with a BF320 vibrating pillow pad to warn the hearing impaired of a potential fire alarm or evacuation alert condition. It is compatible with all C-TEC fire alarm and evacuation alert systems.Key FeaturesLocking mini-XLR connector and plug arrangement helps prevent accidental pillow pad removalLine monitored for disconnection via an internal 6k8 end of line resistor selectable at the BF320JPSelectable 6K8 pillow pad or 27K jack socket end of line monitoring options for fire alarm or evacuation alert system useCan be used on systems with a 10-30V DC voltage rangeFits on a standard UK 25mm back boxSupersedes the old BF364 jack socket

GBP 19.32
1

C-Tec NC805AS Air Switch

C-Tec NC805AS Air Switch

C-Tec NC805AS Air SwitchThe NC805AS is designed for use with C-TECsNC805P Pneumatic Pad. Applying pressure to the NC805P operates the airswitch which in turn triggers a Standard call when the 6.35mm jack plug on the NC805ASis connected to a compatible call points remote socket.Key FeaturesOperates at a minimum differential air pressure of 0.9 p.s.i pounds per square inch or 6220 Pa pascals 10 at 16CIP Rating IP20Ideal for patients who find it difficult to press buttons

GBP 106.18
1

C-Tec QT644 Floor Pressure Mat

C-Tec QT644 Floor Pressure Mat

C-Tec QT644 Floor Pressure MatThe QT644 floor pressure mat is designed to alert staff to the prospect of a wandering patient in nursing homes hospitals and other care facilities. Fully compatible with our Quantec and 800 Series call systems the mat is manufactured to a high standard with an attractive grey PVC finish and non-slip rubber base.Key FeaturesDesigned to trigger a call when it detects patient foot pressureTypically located alongside a bed to advise staff of wandering patientsCan be connected to a Quantec addressable call system or an 800 Series conventional call system via a remote jack socketTough durable grey PVC finish with a non-slip rubber baseAttractive high-quality design - ideal for use in all types of care facilityCan be wiped-clean using a non-caustic sanitising solutionMeasures 90cm x 60cm 3ft x 2ft. Approx 5mm deepSupplied with a 2m lead and a normally open right-angled jack plugHelps protect infirm residents and dementia sufferers against potential falls by quickly alerting staff if someone gets out of bedHighly sensitiveSimple and reliable operationCan also be used in low-level access control applicationsExcellent discounts for quantity orders

GBP 112.04
1

C-Tec Addressable Compact W-2.4-3.5 Wall VADcw 90dBA Sounder - BF451ACXSR

C-Tec Addressable Compact W-2.4-3.5 Wall VADcw 90dBA Sounder - BF451ACXSR

C-Tec Addressable Compact W-2.4-3.5 Wall VADcw 90dBA Sounder - BF451ACXSROur new BF451ACXSW Compact Addressable Wall VAD cw 90dBA Sounder utilises the latest advances in sounder LED and LED lens technology to provide a truly exceptional W-2.4-3.5 fire alarm warning device.The Compact range of addressable loop-powered devices includes sounders visual alarm devices VADs and combined sounder VADs. They are designed for indoor use with C-TECs ZFPXFP and other Apollo Discovery compatible fire panels. Their purpose is to visually and audibly alert building occupants of a fire alarm.The devices offer low current consumption high sound output ultra-bright white LEDs 7 volume levels 15 selectable tone pairs and built-in short-circuit loop isolators.The sounder and VAD on the combined device can be set to operate independently of each other panel dependent function. All devices are designed to comply with the relevant sections of the fire alarm device standards EN 54-3 Sounders EN 54-23 Visual alarm devices - VADs and EN 54-17 Short-circuit isolators.Other features include seven selectable volume levels 15 tone pairs a flash rate of 0.5Hz once every two seconds and a group addressing function to ensure the synchronised operation of multiple devices.Attractively finished in white polycarbonate the BF451ACXSR comes with an integrated sounder VADbase locking mechanism and a plastic ID tag.The BF451ACXSR can also be used to provide C-3-8 coverage when mounted on a ceiling.Key FeaturesThird-party certified to EN54-3 Sounders EN54-23 VADs and 17 Isolators by Intertek pendingProvides W-2.4-3.5 light distribution when wall mounted min. 0.4 lux over a 2.4 x 3.5m cuboid areaCan also provide C-3-8 light distribution when ceiling mounted min 0.4 lux over a 3 x 8m cylindrical areaImpressive 90dBA sound output 1mUnique C-TEC designed lens maximises light output whilst minimising current drawOnboard short-circuit loop isolator550uA quiescent current14mA alarm current 24V DC VAD lit sounder on maxAttractively finished in red polycarbonate light output is whiteGroup addressing facility allows multiple devices to be operated simultaneously7 selectable volume levels and up to 15 selectable tone pairsAttractive compact design - just 102mm diameter 63mm deepIncludes an integrated sounder to base locking mechanismIP21C ratedLow current consumption means multiple devices can be connected to the loopDIP switch addressedSimple click and twist design and easy-fit base ensures rapid installation timeAlso available in a white plastic housing order code BF451ACXSW

GBP 47.84
1

C-Tec NC805C6 Tail Call Lead 1.8m 6ft

C-Tec NC805C6 Tail Call Lead 1.8m 6ft

C-Tec NC805C6 Tail Call Lead 1.8m 6ftA short 1.8mtail call lead for use with C-TECs Quantec and 800 Series Call Systems. It allows usersto remotely generate Standard calls from armchairs beds etc.Key FeaturesEasily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call pointsActivating the pear push or removing the tail call lead from a call points remote socket will generate a Standard callComprises a pear-shaped call push 1.8m 6ft trailing lead and a 6.35mm remote jack plug.

GBP 13.82
1

C-Tec NC805C14 Tail Call Lead 4.2m 14ft

C-Tec NC805C14 Tail Call Lead 4.2m 14ft

C-Tec NC805C14 Tail Call Lead 4.2m 14ftA long 4.2m tail call lead for use with C-TECs Quantec and 800 Series Call Systems. It allows usersto remotely generate Standard calls from armchairs beds etc.Key FeaturesEasily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call pointsActivating the pear push or removing the tail call lead from a call points remote socket will generate a Standard callComprises a pear-shaped call push 4.2m14ft trailing lead and a 6.35mm remote jack plug

GBP 15.54
1