145 results (0,13424 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec ECU722 SigTEL Network Communication Card

C-Tec ECU722 SigTEL Network Communication Card

C-Tec ECU722 SigTEL Network Communication CardNetwork card allows up to 14 ECU-4 8 16 or 8NTs to be interlinked. To network a controller that has an optional ECU-224 desk controller fitted use an ECU723 interfacenetwork card instead.The ECU722 card transmits speech via a single wiring loop and digital data via two linear RS485 networks. The network should be connected using 4 x 2-core 1.5 mm2 enhanced fire-rated cable. Max. length of all networks is 1 km.Key FeaturesAn optional system expansion device.Allows up to 14 ECU-4 8 16 or 8NT SigTEL controllers to be interlinked.One card required per networked SigTEL controller.Allows systems of up to 224 lines 14x ECU-16controllers to be easily set-up.Any ECU-4ECU-8 or ECU-16 can take control of the system at any time by the input of a special code.Note that for networked systems that do not require multiple control points controllers without handsets are available ECU-8NT.IMPORTANT To network a controller that has an optional ECU-224 desk controller fitted use an ECU723 interfacenetwork card instead of an ECU722 the ECU723 is due for release Nov 2019.

GBP 90.65
1

C-Tec XFP761 XFP Network Card For 16 Zone Panels

C-Tec XFP761 XFP Network Card For 16 Zone Panels

C-Tec XFP761 XFP Network Card For 16 Zone PanelsThe XFP network card allows for the connection of up to eight mainpanels any mix over a two-wire RS485 network spanning up to 1KM. Eachnetworked XFP panel can be programmed to receive fire alerts faults andcontrol commands such as silencing alarm sounders and resetting controlpanels from other connected panels.Key FeaturesCan be used to connect up to 8 XFP repeaters any mix toone XFP main panelUp to 500m of cable may be fitted to an XFP two-wirerepeater networkEach XFP repeater offers all the functions and controls ofan XFP main panelThe XFP main panel must have a network communication cardfittedIt is not possible to mix XFP main panels and XFP repeaterson the same networkOne XFP761 required per networked Main XFP Single Loop 16Zone fire panel note that XFP510-16 and XFP510-32 repeaters include a networkdriver card as standardThe XFP761 is NOT compatible with XFP 12 Loop32 Zone fire panels which require an AFP711 card for networking

GBP 74.52
1

C-Tec QTS25 Quantec Surveyor2 IOT Card cw 12 Months Surveyor2 Access

C-Tec QTS25 Quantec Surveyor2 IOT Card cw 12 Months Surveyor2 Access

C-Tec QTS25 Quantec Surveyor2 IOT Card cw 12 Months Surveyor2 AccessQuantec Surveyor2 IOT Card cw 12 months Surveyor2 access Includes IOT connection card web browser access emailable reports up to 5 mobile device connections for pushSMS messaging. 1 x QTS25 per Quantec Controller must be firmware rev 10A9 or above.Anew secure remote Cloud based data management software solution for C-TECs Quantec Addressable Call System.One QTS25 IOT card pictured required per Quantec Controller. Once connected provides 12 months access to ourSurveyor2 monitoring service yearly renewalfeeapplies see Order Codes Pricingtab below.Allows detailed reports on all aspects of call system activity to be accessed onsite or offsite via aninternet browser.Price includes5user accounts with full mobile device connectivity.User configurable dashboards Key Performance Indicator settings and remote access capabilities.Providesvaluable information on call history busiest shifts staff response times busiest rooms and more.Ideal for evaluating staff performance patient demands and determining labour levelsshift patterns.

GBP 783.10
1

C-Tec CFP Relay Output Card Reset Fault Aux amp Remote Relay Outputs CFP762

C-Tec CFP Relay Output Card Reset Fault Aux amp Remote Relay Outputs CFP762

C-Tec CFP Relay Output Card Reset Fault Aux Remote Relay Outputs CFP762An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Outputs are NOT designed to switch mains voltages.

GBP 46.63
1

C-Tec ECU723 SigTEL InterfaceNetwork Communication Card

C-Tec ECU723 SigTEL InterfaceNetwork Communication Card

C-Tec ECU723 SigTEL InterfaceNetwork Communication CardECU-224 interfacenetwork card. Allows an ECU-224 desk controller to be connected to an ECU-4 8 or 16. Can also act as a network card if networking is required. NOT compatible with ECU-8NT Controllers.The ECU723 transmits speech via a single wiring loop and digital data via two linear RS485 networks. The network should be connected using 4 x 2-core 1.5 mm2 enhanced fire-rated cable. Max. length of all networks is 1 km.An optional system expansion device.Allows anECU-224 desk controller to be connected to an ECU-4 8or16 SigTEL controller to simplify call handling on larger SigTEL applications.Mounts inside an ECU-4 8 or 16 can alsobe used tonetworkthe ECU-4 8 or 16 to another controller if required.Not compatible with ECU-8NT controllers.See schematicfull instructions for further details

GBP 108.77
1

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications CardAn optional system expansion device for use with XFP 12 Loop 32 Zone fire panels. Allowsthe connection of up to eight XFP Repeaters or eight XFP Main panels any mix on an RS485 network. One AFP711 card required per networked Main XFP 12 Loop 32 Zone panel note that XFP510-16 and XFP510-32 repeaters include a network driver card as standard.The AFP711 is NOT compatible with XFP Single Loop 16 Zone panels which require a CFP761 card for networking.Key network protocol features when used for interconnecting XFP main panelsCan be used to connect up to 8 XFP main panels any mix over a two-wire RS485 network of up to 1KM in length.Each networked XFP can be programmed to accept Fires Faults and Control actions such as Silence Alarm Sounders and Control Panel Resets from other panels.Each XFP will accept Disablement commands for zones sounders and output sets from other panels.All panels monitored for network wiring faults.Fires and faults on remote panels are displayed on local panels including the point description.CEs can be programmed into local panels dependent on which remote panel is in alarm.The network supports the programming of site data into remote panels from a PC at a local panel.Time and date is common to all panels.All networked main panels require a network communication card.It is not possible to mix XFP main panels and XFP repeaters on the same network.Key network protocol features when used for connecting XFP repeatersCan be used to connect up to 8 XFP repeaters any mix to one XFP main panel.Up to 500m of cable may be fitted to an XFP two-wire repeater network.Each XFP repeater offers all the functions and controls of an XFP main panel.The XFP main panel must have a network communication card fitted.It is not possible to mix XFP main panels and XFP repeaters on the same network.

GBP 114.65
1

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761An optional system expansion device for use with CFP Standardand CFPAlarmSense conventional fire panels.This part must be used if you require the use of a repeater panel or you wish to network compatible XFP panels together.Key FeaturesAllows the connection of up to eight CFP760 Repeaters one CFP761 required per Main all CFP760 repeaters include a CFP761 as standardCommunicates over screened two-wire fire resistant cableTotal repeater network cable length should not exceed 1KM

GBP 61.67
1

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP763 Relay Output Card as per CFP762 8 outputs per zone relays

C-Tec CFP Relay Output Card as per CFP762 8 outputs per zone relays CFP763An optional system expansion device for use withCFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels.Key FeaturesProvides four panel-controlled volt free relay outputs reset fault aux. fire and remote and eight output per zone relays.PCB mounts inside the CFP fire panel.Reset relay is active during the panels reset cycle.Fault relay is active in any fault condition. This relay is failsafe and normally energised - if power is removed from the panel the relay will changeover to produce a fault signal.Aux. fire relay is active in an alarm condition provided all relevant delays have expired.Remote relay is active during any Alarm Condition provided all relevant delays have expired.Output per zone relays will changeover when the corresponding zone is in alarm subject to certain conditions - for full details refer to the instructions downloadable below.Outputs are NOT designed to switch mains voltages.

GBP 67.02
1

C-Tec NC899IRR Conventional Key Switch Reset Point

C-Tec NC899IRR Conventional Key Switch Reset Point

C-Tec NC899IRR Conventional Key Switch Reset PointA securekeyswitch-operated reset point specifically designed tocancel Emergency calls generated by anNC312RXC master infrared ceiling receiver. To operate momentarily turn the keyswitch to the isolate position to reset a call. Always return the keyswitch to theON position after resetleaving it inthe isolateposition will disable the NC312RXC receivers emergency call facility.Key FeaturesMounts on a standard UK 25mm single gang flush or surface back box

GBP 38.99
1

C-Tec 24V 5A EN54-4 Switch Mode PSU BF562-5

C-Tec 24V 5A EN54-4 Switch Mode PSU BF562-5

C-Tec 24V 5A EN54-4 Switch Mode PSU BF562-5A powerful 24V 5A switch modedigital hybrid PSU that can be customised to suit your exact requirements. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition.Multiple indicators - supply present general fault fault type aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current helps extend battery life.Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF562-5E encased version also available.Typical UsesIdeal for powering beam detectors auto-dial communicators aspirating smoke detectors auto-open vent systems auxiliary sounder systems or any other device performing a mandatory function of a fire alarm system.

GBP 196.86
1

C-Tec BF560-12E Switch Mode 12v 2A Caged PSU PCB

C-Tec BF560-12E Switch Mode 12v 2A Caged PSU PCB

C-Tec BF560-12E Switch Mode 12v 2A Caged PSU PCBTheBF560-12E is apowerful switch modedigital hybrid PSU that can be customised to suit your exact requirements. The plasticcoveron PSU PCB guards against touching live parts to VDE 0100-410. Includes the same electronics as the BF560-12 LPCBcertified EN54-4A2 boxed 12V 2A PSU.Key FeaturesMetal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures.Includes a single-pole voltfree changeover relay that switches for any fault condition.Includes afault type hazardous voltages present LED.Two selectable battery charge currents.Battery fault impedance limits can be optimised to suit load current helps extend battery life.Mains fail simulation mode.Improved on-board temperature sensor with optional remote sensor.Electronic functions comply with EN50131-6 grades 1-4 for security applications.Additional InformationEN50131-6 POWER SUPPLIES FOR INTRUSION HOLD UP ALARMS CAPABILITYThe BF560-12E has all the electrical functions required to comply with EN50131-6 Grade 4which includes Grades 3 2 and 1. OEM security companies interested in utilising the BF560-12E inside their own EN50131-6 compliant tamper-resistant enclosures should contact our marketing departmentfor further detailson costs and approvals.PSU CUSTOMISATIONThe BF560-12Ecan be customised to suit your exact requirements using a BF423 configurator PC. Configurable parameters include float voltage temperature compensation battery charge rate mA battery impedance and configurableInputOutput settingsPSU STATUS LEDlocated on the PSU PCB1 flash Mains Failure.2 flashes Battery Voltage Low.3 flashes Battery Voltage Critical.4 flashes Charger Failure.5 flashes Charger OK Battery is either actively charging or in float charge.6 flashes No Batteries Fitted indicating DIP Switch 4 position.7 flashes Battery Resistance Fault Level set by DIP Switch 2 position.8flashes Output Over Voltage.BATTERY FAULT MONITORINGThe BF560-12E monitors battery resistance to the requirements of EN54-4A2. The fault threshold is directly related to the ability of the battery to deliver the rated current to the load. For example batteries stored uncharged for long periods during shipment andor distribution degrade leading to increased internal resistance. If a degraded battery is fitted a fault will be shown by the PSU as mandated by EN54-4A2.DATA PORTData on the BF560-12Es status can be extracted from the PSUsbi-directional data port. The data availableincludes thermistor measurements battery terminal voltage system voltage at load terminals battery charge current load current battery impedanceandASCII text string status messages. Extracting this data requires additional equipment and permissions - contact C-TEC for details.

GBP 70.52
1

C-Tec STI-WSS3-9B14-CL STI IP67 Blue Momentary Switch Custom Text

C-Tec STI-WSS3-9B14-CL STI IP67 Blue Momentary Switch Custom Text

C-Tec STI-WSS3-9B14-CL STI IP67 Blue Momentary Switch Custom TextA highly versatile range of attractive Waterproof PushButtons combining unique design quality and value. These aestheticallyappealing lowhigh voltage switches are quick and easy to install. All models are available in a variety of colours with spacefor function marking and operating instructions. The Waterproof Push Buttonseries is tested to IP67.Key FeaturesEmergencyEvacuate ButtonLatching Key-to-ResetMulti-Function Signal DPC SPC

GBP 84.80
1

C-Tec QT631K Quantec Dimentia Care Room Status Controller with Key Switch Reset

C-Tec QT631K Quantec Dimentia Care Room Status Controller with Key Switch Reset

C-Tec QT631K Quantec Dimentia Care Room Status Controller with Key Switch ResetThe Quantec QT631K dementia care room status controller features a key reset and allows staff to isolate certain functions e.g. PIRs during daytime hours to put the room into Presence and to reset calls using a magnetic swipe key. Can also be interfaced to a doorbell unit when the patient presses the doorbell a call is activated.

GBP 73.72
1