41 results (0,13167 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Fireclass 1500080FC Key Switch Cylinder NS106-1

Fireclass 1500080FC Key Switch Cylinder NS106-1

Fireclass 1500080FC Key Switch Cylinder NS106-1The 1500080FC from Fireclass is a NS106-1 Key Switch Cylinder. This 2-position SPST Keylock Switch features chrome-plated zinc alloy die-cast housing and a plastic cover. It also has silver-plated contacts and terminals.Key FeaturesZinc alloy keys chrome plated with plastic coverSilver plated contacts and terminals4 pins tumbler mechanism10mR Maximum contact resistance200MR Insulation resistance 500VDC1000VAC at 1 minute Dielectric strength

GBP 7.33
1

Fireclass 557.202.080FC TLI800EN EN54 Approved Network Card

Fireclass 557.202.080FC TLI800EN EN54 Approved Network Card

Fireclass 557.202.080FC TLI800EN EN54 Approved Network CardThe use of the FireClass Network allows the fragmentation of a number of fire controllers to be drawn into a network system.The Fireclass Net communications network comprises a collection of network interface modules and peripheral equipment that together form a fault resistant and flexible peer-to-peer network for the Fireclass Digital addressable fire systems controllers.One TLI800EN is required per FireClass and is installed onto the FireClass Main Processor board.The TLI800EN is used toConnect up to 24 Fireclass panels or other nodes to a single networkConnect the Emergency display used to display an alarm in case of a System faultSupported network communications mediaShielded twisted pair copper cable RS485 standardFibre optic cable multimode 50125m or 62.5125 mKey FeaturesAll field wiring terminations connect via removable terminal blocksTwo RS-485 connections for twisted pair network communicationsEarth fault detection and isolationOnboard diagnostic LEDs. These indicate network communications activity and TLI800EN module faultsTwo Micro Controller Units. One is used as a backup microprocessor. These provide MCU fault detection and Emergency Mode fire alarm monitoring in the case of MCU failureFire Alarm input Fire Alarm output and RS-485 Emergency Display connections for use in Emergency Mode

GBP 564.25
1

Fireclass 568.800.034FC HVR800 High Voltage Relay Module In D800 Housing

Fireclass 568.800.034FC HVR800 High Voltage Relay Module In D800 Housing

Fireclass 568.800.034FC HVR800 High Voltage Relay Module In D800 HousingThe HVR800 is a non-addressable device designed to allow a low current main rated relay to switch up to 10A. Alternatively a low voltage drive signal such as that provided by the RIM800 or 80 way mimic can be used to switch the integral mains relay.Key FeaturesD800 housing- 5 A 240 VacDimensions WxHxD 42x26.5x74 mmOperating Temperature -25 to 70 CStorage Temperature -45 to 80 CRelative Humidity 95 non-condensing

GBP 90.48
1

Fireclass Prescient 3 Status Lamp Unit SLU 3

Fireclass Prescient 3 Status Lamp Unit SLU 3

Fireclass Prescient 3 Status Lamp Unit SLU 3The FireClass Prescient 3 SLU 3 Status Lamp Unit is a versatile status indication and control module designed for seamless integration with fire alarm and suppression systems. It provides clear event indication manual release functionality and advanced control features such as an Abort switch Timer Hold and an AutoManual Keyswitch ensuring maximum flexibility and safety in fire protection scenarios.Ideal for fire suppression and alarm systems the SLU 3 ensures precise monitoring and intervention making it a critical component for high-risk environments requiring rapid response and advanced control options.Key FeaturesTwo core data link between panel and status unitTwo core power connection between panel and status unitIndication of eventsstatusManual ReleaseAutoManual KeyswitchCountdown timerAbort and hold off switch

GBP 476.34
1

Fireclass IOB800 InputOutput Expansion Module

Fireclass IOB800 InputOutput Expansion Module

Fireclass IOB800 InputOutput Expansion ModuleThe IOB800 inputoutput expansion module is an LPCB approved board that provides 8 up to isolated digital inputs and 8 x 24Vdc relay outputs for providing IO expansion capabilities to the FireClass control panels for interfacing to other fire protection systems and signalling devices. The IOB800 can be driven from either the control panel or from the remote bus.Key FeaturesThe modular design of the FC700 range including slot card exibility makes expansion easier than ever before.

GBP 288.85
1

Fireclass BXM2425U Microprocessor Controlled Power Station

Fireclass BXM2425U Microprocessor Controlled Power Station

Fireclass BXM2425U Microprocessor Controlled Power StationThe BXM2425-U and 50-U are approved by IMQ to EN 54-41997 A12002 and EN60950-12001. The steel housing contains a 2.5 amp or 5 amp switch mode power supply and monitoring board and has space to accommodate 2 x 12V 17Ah sealed lead acid batteries. The 10 front panel LEDs comprehensively indicate the status of the unit.Key FeaturesRobust metal housing.Twin fused outputs.Temperature compensated charging.Deep discharge protection of batteries.Fault relay output.Size 383mm wide x 408mm high x 97mm deep.Weight 4.3 Kg excluding batteries.Supply voltage 230VAC 5060Hz.Comprehensive LED status indication.

GBP 191.20
1

Fireclass BXM2450U Microprocessor Controlled Power Station

Fireclass BXM2450U Microprocessor Controlled Power Station

Fireclass BXM2450U Microprocessor Controlled Power StationThe BXM2425-U and 50-U are approved by IMQ to EN 54-41997 A12002 and EN60950-12001. The steel housing contains a 2.5 amp or 5 amp switch mode power supply and monitoring board and has space to accommodate 2 x 12V 17Ah sealed lead acid batteries. The 10 front panel LEDs comprehensively indicate the status of the unit.Key FeaturesRobust metal housing.Twin fused outputs.Temperature compensated charging.Deep discharge protection of batteries.Fault relay output.Size 383mm wide x 408mm high x 97mm deep.Weight 4.3 Kg excluding batteries.Supply voltage 230VAC 5060Hz.Comprehensive LED status indication.

GBP 207.49
1

Fireclass 508.031.746FC BXM2425-B Microprocessor Controlled Power Station

Fireclass 508.031.746FC BXM2425-B Microprocessor Controlled Power Station

Fireclass 508.031.746FC BXM2425-B Microprocessor Controlled Power StationThe BXM2425-U is approved by IMQ to EN 54-41997 A12002 and EN60950-12001. The steel housing contains a 2.5 amp switch mode power supply and monitoring board and has space to accommodate 2 x 12V 17Ah sealed lead acid batteries. The 10 front panel LEDs comprehensively indicate the status of the unit.Key FeaturesRobust metal housingTwin fused outputsTemperature compensated chargingDeep discharge protection of batteriesFault relay outputSize 383mm wide x 408mm high x 97mm deepWeight 4.3 Kg excluding batteriesSupply voltage 230VAC 5060HzComprehensive LED status indicationMax. 25A 276VDCRS485 Bus interface for J408-8 and J424-8 panels

GBP 198.77
1

Fireclass 508.031.747FC BXM2450-B Microprocessor Controlled Power Station

Fireclass 508.031.747FC BXM2450-B Microprocessor Controlled Power Station

Fireclass 508.031.747FC BXM2450-B Microprocessor Controlled Power StationThe BXM2450-B is approved by IMQ to EN 54-41997 A12002 and EN60950-12001. The steel housing contains 5 amp switch mode power supply and monitoring board and has space to accommodate 2 x 12V 17Ah sealed lead acid batteries. The 10 front panel LEDs comprehensively indicate the status of the unit.Key FeaturesRobust metal housingTwin fused outputsTemperature compensated chargingDeep discharge protection of batteriesFault relay outputSize 383mm wide x 408mm high x 97mm deepWeight 4.3 Kg excluding batteriesSupply voltage 230VAC 5060HzComprehensive LED status indicationMax. 5A 276VDCRS485 Bus interface for J408-8 and J424-8 panels

GBP 224.98
1

Fireclass 514.800.805FC FC420CP-I Indoor Call Point with Isolator

Fireclass 514.800.805FC FC420CP-I Indoor Call Point with Isolator

Fireclass 514.800.805FC FC420CP-I Indoor Call Point with IsolatorA comprehensive range of call points for use with FireClass addressable systems using the robust and reliable FireClass open protocol. All the callpoints are designed to enable an alarm signal to be given by a plastic resettable element which means that the call point can be easily reset after it has been activated. Any change in the status of the switch is immediately communicated to the FireClass Control and Indicating Equipment CIE. All call points have an integral short-circuit isolator for monitoring the addressable loop wiring.The integral LED indicator is normally off. When the frangible element is broken an alarm is registered and the LED will illuminate red. If a section of the loop wiring adjacent to the call point is shorted the built-in short-circuit isolator trips isolating the shorted section and the LED is illuminated yellow. The status remains until the short is removed. If required an optional transparent hinged cover may be installed to guard against accidental operation. Both indoor and outdoor versions are available.FC420CP-I Addressable Indoor Call Point is designed to monitor and signal the condition of a switch contact that is operated by activating the deformable plastic element. A short circuit isolator is embedded.Key FeaturesIntegral Short Circuit IsolatorDual Colour LED IndicationEN54-11 CertificationCompact Modern StylingTest Key for Fast TestingIP67 Ingress Protection models for external applications

GBP 38.47
1

Fireclass 514.800.806FC FC421CP-I Outdoor Call Point with Isolator

Fireclass 514.800.806FC FC421CP-I Outdoor Call Point with Isolator

Fireclass 514.800.806FC FC421CP-I Outdoor Call Point with IsolatorA comprehensive range of call points for use with FireClass addressable systems using the robust and reliable FireClass open protocol. All the call points are designed to enable an alarm signal to be given by a plastic resettable element which means that the call point can be easily reset after it has been activated. Any change in the status of the switch is immediately communicated to the FireClass Control and Indicating Equipment CIE. All call points have an integral short-circuit isolator for monitoring the addressable loop wiring.The integral LED indicator is normally off. When the frangible element is broken an alarm is registered and the LED will illuminate red. If a section of the loop wiring adjacent to the call point is shorted the built-in short-circuit isolator trips isolating the shorted section and the LED is illuminated yellow. The status remains until the short is removed. If required an optional transparent hinged cover may be installed to guard against accidental operation. Both indoor and outdoor versions are available.FC421CP-I Addressable Break Glass Call Point is designed to monitor and signal the condition of a switch contact that is operated by activating the deformable plastic element. The FC421CP-I is fitted into a standard weatherproof call point housing. IP67 protection degree.Key FeaturesIntegral short circuit isolatorDual colour LED indicationEN54-11 certificationCompact modern stylingTest key for fast testingIP67 ingress protection models for external applications

GBP 175.49
1

Fireclass 557.202.018FC ANN820 40-Way 20 x Red Yellow 20 x Green Yellow LED Module

Fireclass 557.202.018FC ANN820 40-Way 20 x Red Yellow 20 x Green Yellow LED Module

Fireclass 557.202.018FC ANN820 40-Way 20 x Red Yellow 20 x Green Yellow LED ModuleThe ANN820 is ideal for use as a status moduledisplay for sprinkler panels according to the EN 12845 2004 A22009 standard but has many other potential applications such as fire damper and fire door status monitoring.As a sprinkler status display the REDYELLOW LED would indicate a Water Flow Alarm Fault Indication respectively from a Sprinkler Flow Switch or Alarm Valve and the GREENYELLOW LED would indicate the status of an Alarm Valve. GREEN would indicate the Alarm Valve is open in service and YELLOW would indicate the Alarm Valve is closed or partly closed technical alarm.Key Features20 x RedYellow LEDs20 x GreenYellow LEDs

GBP 383.03
1

Fireclass 508.070.004FC FCG Software Licence 11-24 Panel

Fireclass 508.070.004FC FCG Software Licence 11-24 Panel

Fireclass 508.070.004FC FCG Software Licence 11-24 PanelThe 508.070.004FC is a FCG Software Licence 11-24 Panel.Fireclass Graphics is a new clientserver emergency management system and fire detection graphical user interface designed for use with the FC32 64 and 240 control panels.Fireclass Graphics is a Windows-based graphical interface with a high-resolution colour display and provides annunciation and status of the complete Fireclass detection system using the latest FireClass digital technology and helps monitor and manage an emergency in the event a fire is detected.These pieces of fire detection equipment from Fireclass come with the Fireclass Graphics fire management software which is compatible for between one and four fire alarm panels the network card TLI800EN which links all fire controllers together and a power supply unit.Key FeaturesAdditional software license

GBP 2132.64
1

Fireclass 508.070.005FC FCG Additional Client Licence

Fireclass 508.070.005FC FCG Additional Client Licence

Fireclass 508.070.005FC FCG Additional Client LicenceThe 508.070.005FC is an Additional Client Licence for the Fireclass Graphics Software.Fireclass Graphics is a new clientserver emergency management system and fire detection graphical user interface designed for use with the FC32 64 and 240 control panels.Fireclass Graphics is a Windows-based graphical interface with a high-resolution colour display and provides annunciation and status of the complete Fireclass detection system using the latest FireClass digital technology and helps monitor and manage an emergency in the event a fire is detected.These pieces of fire detection equipment from Fireclass come with the Fireclass Graphics fire management software which is compatible for between one and four fire alarm panels the network card TLI800EN which links all fire controllers together and a power supply unit.Key FeaturesAdditional Client License

GBP 775.85
1

Fireclass 508.070.003FC FCG Software Licence 5-10 Panel

Fireclass 508.070.003FC FCG Software Licence 5-10 Panel

Fireclass 508.070.003FC FCG Software Licence 5-10 PanelThe 508.070.003FC is a FCG Software Licence 5-10 Panel.Fireclass Graphics is a new clientserver emergency management system and fire detection graphical user interface designed for use with the FC32 64 and 240 control panels.Fireclass Graphics is a Windows-based graphical interface with a high-resolution colour display and provides annunciation and status of the complete Fireclass detection system using the latest FireClass digital technology and helps monitor and manage an emergency in the event a fire is detected.These pieces of fire detection equipment from Fireclass come with the Fireclass Graphics fire management software which is compatible for between one and four fire alarm panels the network card TLI800EN which links all fire controllers together and a power supply unit.Key FeaturesAdditional software license

GBP 1659.08
1

Fireclass 508.070.001FC FCG Software Licence - 1 Panel

Fireclass 508.070.001FC FCG Software Licence - 1 Panel

Fireclass 508.070.001FC FCG Software Licence - 1 PanelThe 508.070.001FC is a FCG Software Licence - 1 Panel.Fireclass Graphics is a new clientserver emergency management system and fire detection graphical user interface designed for use with the FC32 64 and 240 control panels.Fireclass Graphics is a Windows-based graphical interface with a high-resolution colour display and provides annunciation and status of the complete Fireclass detection system using the latest FireClass digital technology and helps monitor and manage an emergency in the event a fire is detected.These pieces of fire detection equipment from Fireclass come with the Fireclass Graphics fire management software which is compatible for between one and four fire alarm panels the network card TLI800EN which links all fire controllers together and a power supply unit.Key FeaturesAdditional software license

GBP 543.08
1