274 results (0,20261 seconds)

Show all filters

Brand

Colour

Show all

Size

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kennedy 20/40- Tonne 2 Stage Heavy Duty Air Jack

Kennedy 20/40- Tonne 2 Stage Heavy Duty Air Jack

For use when lifting heavy vehicles such as lorries etc. This industrial air jack has a robust steel chassis, 'T' bar handle with integral air control valve and two extensions for increased lifting height. It requires an air pressure of 116 - 174psi (8 - 12bar) and a supply rate of 105ltr/min (3.7cfm). JTA2040 Air supply: 116 - 174psi (8 - 12bar). Air consumption: 105ltr/min (3.7cfm). Lifting capacity: 20T/40T. Base height: 210mm. Lifting height: 40T - 433mm, 20T - 520mm. Air inlet size: 1/4NTP.

GBP 899.99
1

Kennedy 5-Tonne Trolley Jack

Kennedy 5-Tonne Trolley Jack

Constructed from heavy gauge steel for heavy-duty use with a large diameter saddle for a secure hold under the jacking point. Extra long handle for easy access under bigger vehicles which also tilts and locks in three positions with a built-in handle mounted safety release to prevent accidental lowering of the load. A foot pedal pump and fine adjustment are fitted on the handle for optimum vehicle height. Automatic safety overload protection and rear toe plate for easy positioning.

GBP 559.99
1

Kennedy 10-Tonne Trolley Jack

Kennedy 10-Tonne Trolley Jack

Constructed from heavy gauge steel for heavy-duty use with a large diameter saddle for a secure hold under the jacking point. Extra long handle for easy access under bigger vehicles which also tilts and locks in three positions with a built-in handle mounted safety release to prevent accidental lowering of the load. A foot pedal pump and fine adjustment are fitted on the handle for optimum vehicle height. Automatic safety overload protection and rear toe plate for easy positioning.

GBP 899.99
1

Kennedy 1/2- Tonne Transmission Jack

Kennedy 1/2- Tonne Transmission Jack

Ideal for car and light commercial transmission removal and installation. Fully adjustable universal rotary saddle with adjustable corner brackets and safety chains. Foot operated pump and release valve leaves both hands free to manoeuvre transmission. Wide base with four 3 dia. swivel-type ball bearing castors providing stability and easy manoeuvring. Two-stage flash chromed rams inhibit rust from entering the hydraulic system. Lifts from 875 to 1800mm. Contents TTJ500 Capacity...1/2 Tonne Ram Extensions...2 Minimum Saddle Height...875mm Maximum Saddle Height...1800mm Saddle Size...680x810mm Chain Length...95mm Saddle Tilt Forward...24 Saddle Tilt Back...19 Saddle Tilt Side...+/- 20 Saddle Return Weight...15.8kg (35lbs) Base...695 x 805mm Weight...68.5kg

GBP 719.99
1

100x Kennedy 13/32" Diameter Cobalt Drill for Stainless Steel

100x Kennedy 13/32" Diameter Cobalt Drill for Stainless Steel

HSS-Co Heavy Duty Straight Shank Jobber Drills (Inch) heavy duty drill made of 5% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm, very hard bronze, stainless steels as well as heat and acid resistant steels. Features and Benefits 5% cobalt material with excellent heat resistance Can be used to drill steels with tensile strength up to 1,400 N/mm Specifications Cobalt construction (5%) Point angle: 135 Helix angle: Normal Web thickness: Strengthened Relief angle: Normal Tolerance of diameter: H8 Tolerance of shank: F11 Manufacturing Standard: BS 328, DIN 338B Typical Applications Very hard bronze Stainless steels Acid resistant steels Heat resistant steels

GBP 2499.00
1

Kennedy Mm/in Professional Socket Set 3/4" Square DR 36 Piece

Kennedy Mm/in Professional Socket Set 3/4" Square DR 36 Piece

This 22 piece professional socket set contains 15 chrome vanadium steel bi-hexagon sockets from 22-60mm as well as varying accessories such as a lever type ratchet, sliding T-handle, swivel handle, universal joint and 100, 200 and 410mm extension bars. The set is supplied in a robust fitted case with security padlock hole (padlock sold separately) and cushion grip handle for transportation and protection of your tools and components. Features and Benefits All components are manufactured from chrome vanadium steel with an aluminium free construction for overall durability Mirror finish repels dirt and makes for easy cleaning Supplied in a red plastic moulded case with carrying handle for ease of storage, organisation and transportation of your tools Easy and efficient way of bulking out your toolbox with this comprehensive 22 piece kit Contents Standard sockets: (22, 24, 26, 27, 29, 30, 32, 33, 36, 38, 41, 46, 50, 55 and 60mm) Accessories: Lever type ratchet, sliding t-handle, swivel handle, universal joint, extension bars 100, 200 and 410mm Typical Applications DIY Engineering Automotive

GBP 529.99
1

5x Kennedy 3/8" Square Drive Mechanics Torque Wrench 2.5-11Nm

5x Kennedy 3/8" Square Drive Mechanics Torque Wrench 2.5-11Nm

High quality chrome-plated, polished steel head and retractable torque setting lever. Click and Snap action indicates when the pre-set torque level has been reached. Four easy read scales Nm, kgf.m, lbf.in x10, lbf.ft. Push through square drive connector to instantly reverse action. Knurled grip plastic handle. Complete with factory tested calibration certificate, operating instructions and torque conversion chart. Supplied in a cardboard case. Manufactured to ISO 6789 : 2003 (BS EN 26789 : 2003). Accuracy = 4%.

GBP 699.95
1

96x Kennedy 2.5/16" A/F Deep Impact Socket 1" Sq Dr

96x Kennedy 2.5/16" A/F Deep Impact Socket 1" Sq Dr

1 inch square drive imperial deep impact sockets, manufactured form hardy chrome molybdenum steel with a black oxide coating for improved durability. The laser etched sizing makes it easy and efficient to select the right tool for the fastener. Features and Benefits Manufactured from high quality chrome molybdenum steel Black oxidised finish for improved tool lifespan Permanent laser etched markings for quick and easy tool selection Range of imperial sizes from 1.3/8-2.7/8 inches Standards SAE USA Federal Standard GGG-W-660A

GBP 6719.04
1

Kennedy 175mm Ring Slogging Wrench

Kennedy 175mm Ring Slogging Wrench

Manufactured from forged and hardened steel, these ring slogging spanners also possess machined drive faces to ensure good contact with the fastener. With flat striking faces to allow hammer blows to be used to loosen or tighten stubborn fasteners, the product is available in a variety of metric sizes to ensure you find the correct size for your needs. Features and Benefits Forged steel construction makes for a durable product Flat striking faces enable the product to be struck with a hammer if needed Corrosion-resistant finish bolsters product longevity Available in an array of sizes to suit varying specifications Typical Applications Automotive Construction Plumbing Standards Conforms to DIN 7444

GBP 899.99
1

2000x Kennedy No.0x25mm Pozidriv Screwdriver Bit 1/4" Hex

2000x Kennedy No.0x25mm Pozidriv Screwdriver Bit 1/4" Hex

"Manufactured from chrome plated molybdenum steel, this range of Pozidrive screwdriver bits have a hardness of 58 - 62HRC. Suited for use with both hand and power tools and available to purchase in varying sizes to ensure you have the right size to suit your requirements. Features and Benefits Manufactured from high alloy chrome molybdenum steel for durability Chrome plated to bolster resistance to corrosion and dirt Can be used on both hand and power tools making it a versatile product Available in a variety of sizes and specifications to suit a host of needs Typical Applications Ideal for use with both hand and power tools, the Pozidrive is suited to applications that require a higher torque"

GBP 620.00
1

150x Kennedy 5.00MM Carbide 3 Flute Plain Shank Long Series Ball Nosed End Mills

150x Kennedy 5.00MM Carbide 3 Flute Plain Shank Long Series Ball Nosed End Mills

Long Series - 3 Flute - Metric Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards. Metric Tolerances Diameter: Over 1.00 ~ up to 6.00. Tolerance: +0.000, -0.050. Diameter: Over 6.00 ~ up to 25.00. Tolerance: +0.000, -0.080.

GBP 4498.50
1

150x Kennedy 8.00MM Carbide 3 Flute Plain Shank Long Series Ball Nosed End Mills

150x Kennedy 8.00MM Carbide 3 Flute Plain Shank Long Series Ball Nosed End Mills

Long Series - 3 Flute - Metric Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards. Metric Tolerances Diameter: Over 1.00 ~ up to 6.00. Tolerance: +0.000, -0.050. Diameter: Over 6.00 ~ up to 25.00. Tolerance: +0.000, -0.080.

GBP 7498.50
1

150x Kennedy 12.00MM Carbide 3 Flute Plain Shank Long Series Ball Nosed End Mills

150x Kennedy 12.00MM Carbide 3 Flute Plain Shank Long Series Ball Nosed End Mills

Long Series - 3 Flute - Metric Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards. Metric Tolerances Diameter: Over 1.00 ~ up to 6.00. Tolerance: +0.000, -0.050. Diameter: Over 6.00 ~ up to 25.00. Tolerance: +0.000, -0.080.

GBP 13498.50
1