KlikkMedia | Google Hirdetés X Online Marketing Tanácsadás

Kidde Airsense EST-XAUDIO-48-RS Function Card 4 IN 8 OUT Audio RS485

Kidde Airsense EST-XAUDIO-48-RS Function Card 4 IN 8 OUT Audio RS485This audio intputoutput card is designed for use with a ESTCU-8LCD function slot. It offers 4-line audio inputs via an RJ45 connector as well as 8 symmetrical outputs via an RJ45 connector for leading out audio signals to the external devices or amplifiers of the EST ENT VES system. The card is also equipped with an RS485 interface with the help of which the EST ENT VES system can be controlled or integrated with devices offered by other producers.Key FeaturesCurrent consumption typically 100 mA at 48 VOperating temperature 0C to 70CStandards EN54-16RS485 interface

GBP 673.73

1

Kidde Airsense EST-XCTRLINE-4 Function Card 4 IN 8 OUT Audio RS485

Kidde Airsense EST-XCTRLINE-4 Function Card 4 IN 8 OUT Audio RS485EST-xCTRLN-4 provides 4 independent speaker line outputs A B C D. Card allows to switch between main and spare amplifiers. Line measurement methods can be made by Impedance Loop or End of Line Module EOL. The measurement method is selected from the software configuration.EST-xCTRLN-4 provides fault detection opening ground leakage and surveillance amplifiers on common 100 V Buses.Key FeaturesCurrent consumption 152 mA max. for 48 VPower supply Internal form the Control Unit backplaneType of connector 10 pin screw terminal type PHOENIX 5.08 mmImpedance measurement frequency 1 kHz to 48 kHzFrequency of the signal for EOL modules 18 kHz to 24 kHzMaximum measured current 20 AMaximum measured voltage 200 VAccuracy of measurement Up to 5Physical dimensions 70 x 215 x 30 mm W x H x D

GBP 638.90

1

Kidde Airsense Stratos-Micra 100 Relay Input Card

Stratos-Micra 100 Relay Input CardStratos-Micra 100 has two pipe inlets and supports a maximum of 100 metres of sampling pipe. Stratos-Micra will be available with an optional Piped Exhaust type Docking Station. This is primarily intended to allow the Stratos-Micra detector to sample from areas which may be at different air pressure to the detector location. Typical uses are for air-duct sampling and allowing the installation of the detector in under-floor or ceiling voids or when sampling from pieces of computer related equipment.Stratos-Micra will provide four alarm level outputs and a fault output to the fire alarm panel. Relays for Fire 1 and Fault are fitted as standard. When an addressable panel is used the Addressable Protocol Interface Card APIC is used to communicate using the addressable protocol. By using the APIC means that the alarm and fault relays can be used for other purposes.Stratos-Micra is supplied with comprehensive diagnostic facilities as standard. By simply plugging a PC into the serial port display diagnostic menus will give the capability of fault finding down to individual component level. ClassiFire-3D may be viewed working in real time. It is also possible to view a detailed chart recorder of historical smoke levels showing date time and alarm thresholds.Key FeaturesSmall low cost aspirating smoke detector for easy and discreet installationHigh sensitive provided by laser based forward light scatter for reliable early warningTwo sampling pipes 100m aggregate for flexibilityUnique ClassiFire perceptive artificial intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and the system contaminationUnwanted alarms from dust are avoided using patented dual technology LDD 3D laser dust discrimination and elimination system

GBP 1707.50

1

Kidde Airsense Stratos-Micra 25 Relay Input Card

Stratos-Micra 25 Relay Input CardStratos-Micra 25 is intended to provide LOCALISED incipient fire detection only. This means that it is suitable for the substantial range of applications typified by small non-compartmentalised rooms warehouse racking or pieces of electronic or electromechanical equipment where it is desirable to achieve individual incipient fire reporting. In compartmentalised rooms each compartment would normally use individual Stratos-Micra 25 detectors.This product employs a very low-power aspirator and the aspirating capability of the Stratos-Micra 25 detector is limited accordingly. Stratos-Micra 25 is NOT intended to protect large areas or to sample from areas where there may be any difference in airflow rates or pressure differentials. Application of Stratos-Micra 25 in these circumstances is not recommended. If detection in environments conforming to these descriptions is required alternative versions of Stratos products should be used.We recommend a maximum sampling pipe length of 25 metres to be used on the Stratos-Micra 25. Maximum single length of sampling pipe to be used on the Stratos-Micra 100 detector is 100 metres or 2 x 50 meter lengths in still air with 25 sampling holes or Capillary Remote Sampling Points. This will provide a transport time from the end of the sampling pipe within 120 seconds. If the protected area has airflow present the maximum permitted sampling pipe length will be reduced.Key FeaturesUltra small low cost aspirating smoke detector for easy and discreet installationHigh sensitivity provide by laser based forward light scatter for reliable early warningSignal sampling pipe up to 50m in lengthUnique ClassiFire perceptive artificial intelligent system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protect environment and dust separation system contaminationUnwanted alarm from dust are avoided using patented Dual TechnologyLDD 3D Laser Dust Discrimination and elimination system

GBP 1285.96

1

Kidde Airsense EST-CU-8LCD Control Unit - 8 Control Slots 4 Function Slots

Kidde Airsense EST-CU-8LCD Control Unit - 8 Control Slots 4 Function SlotsESTCU-8LCD Control Unit CU is a matrix mixer of input signals which routes to 4 x 100 V internal audio buses a 45-channel digital system buses or directly to audio outputs in a unit.In basic factory configuration EST-CU-8LCD is a stand-alone system which enables only connections with DFMS and zone microphones.For networking with other CU optional xNet card is needed.The CU is equipped with 1x EST-xCtrLine-4 card in slot 1 1x ESTAudIO-48-RS card in slot A and 1x EST-LogIN-8f card in slot B. Slot C and D can extend control unit audio dsp abilities up to 24 audio outputs 12 audio inputs. Slots from 2 to 7 are free for any cards assignment EST-xCtrLine-24 and EST-xLogINOUT.Furthermore EST-CU-8LCD is equipped with an LCD touch screen with a control module which allows easy access to management functions and monitoring of the whole system.Key Features Network-based system allowing configuration diagnostics and management via EthernetManaging up to 254 devices on the network7 slots available for any configuration of loudspeaker control cards control input and output cardsAdditional 2 slots designated for audio inputoutput cards and control input output cardsUp to 8 messages played simultaneously in different zonesUp to 32GB SD flash memory designated for playback and recording messages 48 kHz 16 bitSupport of up to 12 secured amplifiersOptional equipment EST-xNET-1GbWANRS for optical fibre redundant connectionIntegrated DSP with implemented 3 band parametric EQ on all inputs on control units 8 band parametric EQ delay lines audio limiter and feedback eliminator on each of the audio outputsComprehensive solution based on RS485 functionality enabling seamless integration of the EST ENT VES system with 3rd party systems thanks to implementation of standard and proprietary communication interfaces

GBP 1953.20

1

Kidde Airsense EST-VES-2001-LN Integrated Mini PAVA Unit 2xAB 4 Lines

Kidde Airsense EST-VES-2001-LN Integrated Mini PAVA Unit 2xAB 4 LinesThe Kidde Airsense Integrated Mini PAVA Unit is 2xAB 4 lines amp 2x160W inc. spare amp. 1xaudio LCD fiber network card fireman mic charger wo batteriesKey FeaturesStandalone or TCP IP network connectionComplete wall mount system - EN54-4 16Speaker impedance monitoringRemote managementUp to 254 networked devices including fire and zone microphonesNetwork connection possible via optical fiber copper or both.Digital audio signal processing built-inAbility to perform evacuation messages and music playbackProfessional quality sound

GBP 3359.02

1

Kidde FRG2064C-99 Global Repeater - 16-64 Zone - 230v English

Kidde FRG2064C-99 Global Repeater - 16-64 Zone - 230v EnglishThe FRG2064C is a repeateremulator with 16 fire and fault zones expandable to 64 used in FP12002000C series networked systems.The repeater is connected on the fire panel network and can operate in a local or global repeater mode. An 80 x 40 character backlit graphic display and full indication and control keyboard is provided standard.Key FeaturesFull system controlGlobal zone and global panel supportZone LED text supported on the user interfaceRS485 network card includedFull range of LON700 device support

GBP 2405.56

1

Kidde 2X-AT-F2-S Addressable Fire Panel Touch Screen With UI - 2 Loop Small CAB

Kidde 2X-AT-F2-S Addressable Fire Panel Touch Screen With UI - 2 Loop Small CABAn addressable fire panel with 7 touch screen UI and small CAB. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSMounting Type Surface MountMaterial Steel paintedWhite colour

GBP 1133.33

1

Kidde 2X-AT-F2-P Addressable Fire Panel Touch Screen With UI - 2 Loop Big PSU

Kidde 2X-AT-F2-P Addressable Fire Panel Touch Screen With UI - 2 Loop Big PSUAn addressable fire panel with 7 touch screen UI and big PSU. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSMounting Type Surface MountMaterial Steel paintedWhite colour

GBP 1438.20

1

Kidde 2X-AT-F2-FB-S Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Small CAB

Kidde 2X-AT-F2-FB-S Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Small CABAn addressable fire panel with 7 touch screen UI and FB Control. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colour

GBP 1209.06

1

Kidde 2X-AT-F2 Addressable Fire Panel Touch Screen With UI - 2 Loop

Kidde 2X-AT-F2 Addressable Fire Panel Touch Screen With UI - 2 LoopAn addressable fire panel with 7 touch screen and UI. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colourDimensions 446 x 536 x 164 mm

GBP 1133.33

1

Kidde 2X-AT-F2-FB-P Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Big PSU

Kidde 2X-AT-F2-FB-P Addressable Fire Panel Touch Screen With UI FB Control - 2 Loop Big PSUAn addressable fire panel with 7 touch screen UI and FB Control. 2 loops.Key Features2 high power loops expandable to 4 with 500 mA per loop7 touch screenHigh loop power PAK to increase loop power from 500 mA to 800 mAEthernet port with TCPIP for remote diagnosis maintenance and programmingAll pluggable connectors3 USB ports with memory card support and RS232 for printer supportCommunication through the UltraSync cloud using the EN 54-21 UC240 UltraSync communicatorIntegration into ATS8600 management software allowing integration with security systems and CMSPower 110 240 VacSupported batteries Max. 2 x 12V 18AhMounting Type Surface MountMaterial Steel paintedWhite colour

GBP 1513.93

1

Kidde Airsense EST-CU-11LT Control Unit 11 control slots

Kidde Airsense EST-CU-11LT Control Unit 11 control slotsESTCU-11LT Control Unit CU is a matrix mixer of input signals which routes to 4 x 100 V internal audio buses a 45-channel digital system buses or directly to audio outputs in a unit. EST-CU-11LT is designed to work for small PA VE systems or as an extension unit in more complex systems. It means that the CU can function independently as the central unit of a small system or be part of a large complex system for which it represents another level of either territorial extension operation in a remote structure or functional extension operation of further fire zones and loudspeaker lines in such a structure.The modular design of the CU and its flexibility enables optimization of equipment and cost efficiency regardless of size number of structures their location and connectivity.In the event of losing connectivity with a networked master unit ESTCU-11LT is able to perform fire alarm scenarios independently thanks to the configuration recorded locally. While attached to the main communication ring of the system EST-CU-11LT can control amplifiers and power supply managers as well as receive alarm and digital signals and send them to other system devices.EST-CU-11LT Control Unit distributes audio signals to individual zones and ensures that individual zones function properly. It also controls the condition of loudspeaker lines and amplifiers.If a fault is detected it sends the signal to the system and automatically switches to a backup amplifier. The CU is equipped with an EST-cAudIO-412 card offering 4 symmetrical line audio inputs and 12 symmetrical outputs to lead audio signals out to external devices or amplifiers of the EST ENT VES system.Key FeaturesCompliance with EN54-16Network-based system allowing configuration diagnostics andmanagement via EthernetManaging up to 254 devices on the network11 slots available for any configuration of loudspeaker control cards andcontrol input output cardsBuilt-in audio card with 4 inputs and 12 audio outputsUp to 12 messages played simultaneously in different zonesUp to 32 GB SD flash memory designated for playback and recordingmessages 48 kHz 16 bit1x POE portSupport of up to 12 secured amplifiersBuilt-in 2 control inputs and outputs2x 1 GB ports available for system extensionIntegrated DSP with implemented 3 band parametric EQ on all inputs oncontrol units 8 band parametric EQ delay lines audio limiter andfeedback eliminator on each of the audio outputsComprehensive solution based on RS485 functionality enablingseamless integration of the EST ENT VES system with 3rd partysystems thanks to implementation of standard and proprietarycommunication interfaces

GBP 1823.00

1

Kidde Airsense EST-CU-11LCD Control Unit with LCD 11 control slots

Kidde Airsense EST-CU-11LCD Control Unit with LCD 11 control slotsESTCU-11LT Control Unit CU is a matrix mixer of input signals which routes to 4 100 V internal audio buses a 45-channel digital system buses or directly to audio outputs in a unit.EST-CU-11LT is designed to work for small PA VE systems or as an extension unit in more complex systems.It means that the CU can function independently as the central unit of a small system or be part of a large complex system for which it represents another level of either territorial extension operation in a remote structure or functional extension operation of further fire zones and loudspeaker lines in such a structure.The modular design of the CU and its flexibility enables optimization of equipment and cost efficiency regardless of size number of structures their location and connectivity. In the event of losing connectivity with a networked master unit ESTCU-11LT is able to perform fire alarm scenarios independently thanks to the configuration recorded locally. While attached to the main communication ring of the system EST-CU-11LT can control amplifiers and power supply managers as well as receive alarm and digital signals and send them to other system devices.EST-CU-11LT Control Unit distributes audio signals to individual zones and ensures that individual zones function properly. It also controls the condition of loudspeaker lines and amplifiers. If a fault is detected it sends the signal to the system and automatically switches to a backup amplifier.The CU is equipped with an EST-cAudIO-412 card offering 4 symmetrical line audio inputs and 12 symmetrical outputs to lead audio signals out to external devices or amplifiers of the EST ENT VES system. Furthermore EST-CU-11LT can be equipped with an LCD touch screen with a control module which allows easy access to management functions and monitoring of the whole system such extended configuration is included in EST-CU-11LCD Control Unit.Key FeaturesCompliance with EN54-16Network-based system allowing configuration diagnostics andmanagement via EthernetManaging up to 254 devices on the network11 slots available for any configuration of loudspeaker control cards andcontrol input output cardsBuilt-in audio card with 4 inputs and 12 audio outputsUp to 12 messages played simultaneously in different zonesUp to 32 GB SD flash memory designated for playback and recordingmessages 48 kHz 16 bit1x POE portSupport of up to 12 secured amplifiersBuilt-in 2 control inputs and outputs2x 1 GB ports available for system extensionIntegrated DSP with implemented 3 band parametric EQ on all inputs oncontrol units 8 band parametric EQ delay lines audio limiter andfeedback eliminator on each of the audio outputsComprehensive solution based on RS485 functionality enablingseamless integration of the EST ENT VES system with 3rd partysystems thanks to implementation of standard and proprietarycommunication interfaces

GBP 2213.64

1

Kidde Airsense Stratos-Micra 100 9-30672

Stratos-Micra 1009-30672Stratos-Micra 100 has two pipe inlets and supports a maximum of 100 metres of sampling pipe. Stratos-Micra will be available with an optional Piped Exhaust type Docking Station. This is primarily intended to allow the Stratos-Micra detector to sample from areas which may be at different air pressure to the detector location. Typical uses are for air-duct sampling and allowing the installation of the detector in under-floor or ceiling voids or when sampling from pieces of computer related equipment.Stratos-Micra will provide four alarm level outputs and a fault output to the fire alarm panel. Relays for Fire 1 and Fault are fitted as standard. When an addressable panel is used the Addressable Protocol Interface Card APIC is used to communicate using the addressable protocol. By using the APIC means that the alarm and fault relays can be used for other purposes.Stratos-Micra is supplied with comprehensive diagnostic facilities as standard. By simply plugging a PC into the serial port display diagnostic menus will give the capability of fault finding down to individual component level. ClassiFire-3D may be viewed working in real time. It is also possible to view a detailed chart recorder of historical smoke levels showing date time and alarm thresholds.Key FeaturesSmall low cost aspirating smoke detector for easy and discreet installationHigh sensitive provided by laser based forward light scatter for reliable early warningTwo sampling pipes 100m aggregate for flexibilityUnique ClassiFire perceptive artificial intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and the system contaminationUnwanted alarms from dust are avoided using patented dual technology LDD 3D laser dust discrimination and elimination system

GBP 1585.55

1

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display Module

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display ModuleModuLaser is a scalable aspirating smoke detection solution thatmakes installation easier maintenance quicker and takes applicationsfurther than traditional air sampling detectors. Two basic module typescomprise the ModuLaser solution a display module and a detectormodule. Each detector module can accommodate up to 250 meterscombined sampling pipe. Display modules and detector modulescommunicate by RS-485 interconnections.Display modules are available in three configurations Standard withTFT colour display status LEDs and navigation buttons Minimum withonly status LEDs and Command which is similar to the Standard butwith the added functionality to control various modules overSenseNET. The Minimum and Standard Display Modules can eachsupport up to 8 detector modules while the Command Display Modulecan support up to 127 modules across the SenseNET network.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see color TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 487.51

1

Kidde Airsense EST-VES-4001-LN PAVA EST Voice Evacuation System

Kidde Airsense EST-VES-4001-LN PAVA EST Voice Evacuation System4xAB 8 lines amp 2x320W inc. spare amp. 1xaudio LCD fibre network card fireman mic. charger wo batteriesEST VES is scalable Public Address Voice Alarm unit suitable for multi-purpose architectures. Devices from EST VES series are voice alarm compact control units containing all components within one compact housing which meet all the requirements of EN 54-16 and EN 54-4 certificate of constancy of performance 1438-CPR-XXXX.Whole concept of the system is based on the high quality audio network distribution nodes equipped either with two independent 160 W or 320 W class D amplifiers which distribute 100 V signals to 4 or 8 speaker lines depending on the type. The system also ensures operation of a backup amplifier for the Emergency priority type of signals.EST VES is equipped with integrated backup power supply and EN 54-4 compliant charging unit. EST VES is designed to be a Plug Play device with all elements expected from Voice Evacuation Systems including a built-in fire microphone touchscreen for global control DSP programmable contact inputs and buttons time scheduler charger with battery mounting space and expandable memory size for messages all fitted into IP30 chassis.EST VES belongs to the family of independent EVAC systems which can be networked together and extended by desktop zone microphones or fireman microphones via TCPIP network to provide live announcements and background music inputs. The system has been designed to be wired using CAT5 cables for paging microphones and fibre-optic redundant interlink connections between the systems.EST VES support up to 45 high quality audio signals distributed over 254 devices in the network.Key FeaturesStand alone or TCPIP network architectureAll in one independent wall mount EN 54-4 16 PAVA unitImpedance speaker monitoringRemote managementUp to 254 devices can be connected on the network incl. fireman and zone microphonesAbility to connect standalone EST VES units via fibre optic copper or both cables. Compatibility with RACK mounted modular EST ENT VESDSP audio processing on boardProfessional Sound QualityEvacuation paging message and background music featuresSimple installationUser friendly and intuitive programming software

GBP 4043.26

1

Kidde Airsense EST-VES-4002-LN PAVA EST Voice Evacuation System

Kidde Airsense EST-VES-4002-LN PAVA EST Voice Evacuation System4xAB indep. 8 lines amp. 2x320W inc. spare amp. 2xaudio LCDfiber network card fireman mic. charger wo batteriesEST VES is scalable Public Address Voice Alarm unit suitable for multi-purpose architectures. Devices from EST VES series are voice alarm compact control units containing all components within one compact housing which meet all the requirements of EN 54-16 and EN 54-4 certificate of constancy of performance 1438-CPR-XXXX.Whole concept of the system is based on the high quality audio network distribution nodes equipped either with two independent 160 W or 320 W class D amplifiers which distribute 100 V signals to 4 or 8 speaker lines depending on the type. The system also ensures operation of a backup amplifier for the Emergency priority type of signals.EST VES is equipped with integrated backup power supply and EN 54-4 compliant charging unit. EST VES is designed to be a Plug Play device with all elements expected from Voice Evacuation Systems including a built-in fire microphone touchscreen for global control DSP programmable contact inputs and buttons time scheduler charger with battery mounting space and expandable memory size for messages all fitted into IP30 chassis.EST VES belongs to the family of independent EVAC systems which can be networked together and extended by desktop zone microphones or fireman microphones via TCPIP network to provide live announcements and background music inputs. The system has been designed to be wired using CAT5 cables for paging microphones and fibre-optic redundant interlink connections between the systems.EST VES support up to 45 high quality audio signals distributed over 254 devices in the network.Key FeaturesStand alone or TCPIP network architectureAll in one independent wall mount EN 54-4 16 PAVA unitImpedance speaker monitoringRemote managementUp to 254 devices can be connected on the network incl. fireman and zone microphonesAbility to connect standalone EST VES units via fibre optic copper or both cables. Compatibility with RACK mounted modular EST ENT VESDSP audio processing on boardProfessional Sound QualityEvacuation paging message and background music featuresSimple installationUser friendly and intuitive programming software

GBP 4306.37

1

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 948.44

1

Kidde AirSense Stratos ModuLaser Detector Module 9-30783

Kidde AirSense Stratos ModuLaser Detector Module 9-30783ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 856.82

1

Kidde AirSense Stratos ModuLaser Standard Display Module 9-30781

Kidde AirSense Stratos ModuLaser Standard Display Module 9-30781ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.The Standard Display Module features a user interface which consist of a TFT colour display navigation buttons and status LEDs. Configuration of the Standard Display Module and associated detectors modules can be done via the user interface via a computer using Remote software or via SenseNET using a Command Display Module. The TFT colour display support simple operations like changing configuration options via a menu driven structure but also advanced features like viewing the chart recording in graphical format.The Standard Display Module has two USB ports one master and one slave. The master is used to connect a pen drivememory stick which in turn can be used for storing the configuration the event logs or chart recordings or for firmware upgrade purposes. While the USB slave is used to connect to a computer.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 1066.99

1

Kidde AirSense Stratos ModuLaser Command Display Module 9-30782

Kidde AirSense Stratos ModuLaser Command Display Module 9-30782ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.The Standard Display Module features a user interface which consist of a TFT colour display navigation buttons and status LEDs. Configuration of the Standard Display Module and associated detectors modules can be done via the user interface via a computer using Remote software or via SenseNET using a Command Display Module. The TFT colour display support simple operations like changing configuration options via a menu driven structure but also advanced features like viewing the chart recording in graphical format.The Standard Display Module has two USB ports one master and one slave. The master is used to connect a pen drivememory stick which in turn can be used for storing the configuration the event logs or chart recordings or for firmware upgrade purposes. While the USB slave is used to connect to a computer.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 1832.20

1

Performance Marketing Agency

Gain the Advantage with KlikkMedia

Brand

Merchant

Price (EUR)