7 results (0,13637 seconds)

Show all filters

Brand

Size

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Weg CFW08 0027T 3848 EOFAZ Size 2 Variable Speed Drive

Weg CFW08 0027T 3848 EOFAZ Size 2 Variable Speed Drive

The WEG CFW series is intended for speed control of three-phase induction motors. CFW-08 Easy to install and operate. Equipped with optimised software that can be easily set through a keypad, which enables the drive to process and control industrial machines. In addition, the CFW08 Plus series was designed with dead time compensation techniques, which avoids motor instability and provides torque increase at low speeds. Standard Features: IP20 and IP66 enclosure with V/Hz and sensorless vector control. Single and three-phase input power supply 200 - 240V, input voltage. 150% current overload capacity (during 60s every 10min). 2.5/5/10/15kHz adjustable IGBT's switching frequency. Protective Features: overcurrent, motor overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and undervoltage and external fault. Control Features: linear and 'S' acceleration and deceleration ramps, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profile, maximum and minimum adjustable frequency limits, two skip frequencies, adjustableoutput current limit, JOG, ride-thru and flying start, process regulator - PID. Applications: pumps, fans, blowers, mixers, conveyors, winding/unwinding. CFW08 400V 3AC Variable Speed Drives IP66

GBP 499.99
1

Weg SSW06 0085T 2257 ESZ Size 2 Electronic Soft Start

Weg SSW06 0085T 2257 ESZ Size 2 Electronic Soft Start

SSW-06 Series Soft-Starters are static starters intended to accelerate, decelerate and protection of three phase induction motors. The control of the voltage applied to the motor by the means of the thyristors triggering angle variation, allows the soft-start to start and stop smoothly an electric motor. With adequate adjustments of the variables, the torque produced is adjusted to the needs of the load, so the required current is going to be as low as possible for the starting procedure.Standard Features: 220-575 or 575-690 V 50/60Hz input voltage supply. HMI with double display (LED & LCD). Built-in By-pass up to 820A. Soft-StartersSoft-Starters are static starters that accelerate, decelerate and protect three phase induction motors. The control of the voltage applied to the motor allows the soft-starter to start and stop an electric motor smoothly.

GBP 1099.99
1

Weg CFW08 0100T 3848 EOFAZ Size 2 Variable Speed Drive

Weg CFW08 0100T 3848 EOFAZ Size 2 Variable Speed Drive

The WEG CFW series is intended for speed control of three-phase induction motors. CFW-08 Easy to install and operate. Equipped with optimised software that can be easily set through a keypad, which enables the drive to process and control industrial machines. In addition, the CFW08 Plus series was designed with dead time compensation techniques, which avoids motor instability and provides torque increase at low speeds. Standard Features: IP20 and IP66 enclosure with V/Hz and sensorless vector control. Single and three-phase input power supply 200 - 240V, input voltage. 150% current overload capacity (during 60s every 10min). 2.5/5/10/15kHz adjustable IGBT's switching frequency. Protective Features: overcurrent, motor overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and undervoltage and external fault. Control Features: linear and 'S' acceleration and deceleration ramps, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profile, maximum and minimum adjustable frequency limits, two skip frequencies, adjustableoutput current limit, JOG, ride-thru and flying start, process regulator - PID. Applications: pumps, fans, blowers, mixers, conveyors, winding/unwinding. CFW08 400V 3AC Variable Speed Drives IP66

GBP 699.99
1

Weg SSW06 0130T 2257 ESZ Size 2 Electronic Soft Start

Weg SSW06 0130T 2257 ESZ Size 2 Electronic Soft Start

SSW-06 Series Soft-Starters are static starters intended to accelerate, decelerate and protection of three phase induction motors. The control of the voltage applied to the motor by the means of the thyristors triggering angle variation, allows the soft-start to start and stop smoothly an electric motor. With adequate adjustments of the variables, the torque produced is adjusted to the needs of the load, so the required current is going to be as low as possible for the starting procedure.Standard Features: 220-575 or 575-690 V 50/60Hz input voltage supply. HMI with double display (LED & LCD). Built-in By-pass up to 820A. Soft-StartersSoft-Starters are static starters that accelerate, decelerate and protect three phase induction motors. The control of the voltage applied to the motor allows the soft-starter to start and stop an electric motor smoothly.

GBP 1439.99
1

Weg CFW08 0065T 3848 EOFAZ Size 2 Variable Speed Drive

Weg CFW08 0065T 3848 EOFAZ Size 2 Variable Speed Drive

The WEG CFW series is intended for speed control of three-phase induction motors. CFW-08 Easy to install and operate. Equipped with optimised software that can be easily set through a keypad, which enables the drive to process and control industrial machines. In addition, the CFW08 Plus series was designed with dead time compensation techniques, which avoids motor instability and provides torque increase at low speeds. Standard Features: IP20 and IP66 enclosure with V/Hz and sensorless vector control. Single and three-phase input power supply 200 - 240V, input voltage. 150% current overload capacity (during 60s every 10min). 2.5/5/10/15kHz adjustable IGBT's switching frequency. Protective Features: overcurrent, motor overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and undervoltage and external fault. Control Features: linear and 'S' acceleration and deceleration ramps, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profile, maximum and minimum adjustable frequency limits, two skip frequencies, adjustableoutput current limit, JOG, ride-thru and flying start, process regulator - PID. Applications: pumps, fans, blowers, mixers, conveyors, winding/unwinding. CFW08 400V 3AC Variable Speed Drives IP66

GBP 639.99
1

Weg SSW06 0060T 2257 ESZ Size 2 Electronic Soft Start

Weg SSW06 0060T 2257 ESZ Size 2 Electronic Soft Start

SSW-06 Series Soft-Starters are static starters intended to accelerate, decelerate and protection of three phase induction motors. The control of the voltage applied to the motor by the means of the thyristors triggering angle variation, allows the soft-start to start and stop smoothly an electric motor. With adequate adjustments of the variables, the torque produced is adjusted to the needs of the load, so the required current is going to be as low as possible for the starting procedure.Standard Features: 220-575 or 575-690 V 50/60Hz input voltage supply. HMI with double display (LED & LCD). Built-in By-pass up to 820A. Soft-StartersSoft-Starters are static starters that accelerate, decelerate and protect three phase induction motors. The control of the voltage applied to the motor allows the soft-starter to start and stop an electric motor smoothly.

GBP 799.99
1

Weg CFW08 0043T 3848 EOFAZ Size 2 Variable Speed Drive

Weg CFW08 0043T 3848 EOFAZ Size 2 Variable Speed Drive

The WEG CFW series is intended for speed control of three-phase induction motors. CFW-08 Easy to install and operate. Equipped with optimised software that can be easily set through a keypad, which enables the drive to process and control industrial machines. In addition, the CFW08 Plus series was designed with dead time compensation techniques, which avoids motor instability and provides torque increase at low speeds. Standard Features: IP20 and IP66 enclosure with V/Hz and sensorless vector control. Single and three-phase input power supply 200 - 240V, input voltage. 150% current overload capacity (during 60s every 10min). 2.5/5/10/15kHz adjustable IGBT's switching frequency. Protective Features: overcurrent, motor overload, drive over temperature, output phase-to-phase and phase-to-ground short circuit, DC bus over and undervoltage and external fault. Control Features: linear and 'S' acceleration and deceleration ramps, local/remote control, DC braking, torque boost, motor slip compensation, electronic pot, preset speeds, adjustable V/Hz profile, maximum and minimum adjustable frequency limits, two skip frequencies, adjustableoutput current limit, JOG, ride-thru and flying start, process regulator - PID. Applications: pumps, fans, blowers, mixers, conveyors, winding/unwinding. CFW08 400V 3AC Variable Speed Drives IP66

GBP 559.99
1