23 results (0,16334 seconds)

Show all filters

Brand

Colour

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Mini Oak-ish Curved Bedside with Open Slot

Mini Oak-ish Curved Bedside with Open Slot

The mini version of our famous IN711, this small but handy bedside makes a perfect stand for nibbles, drinks, or a lamp. It will prove handy all over your home and is made from 100% solid mango wood in a fine oak-ish finish. It has curved edges which will fit into any home/living space. It also comes with 1 drawer, 1 open slot and 4 Nordic style legs. This petite product is part of Recession Collection. Dimensions (mm) : 300D 550H 300W 300D 550H 300W

GBP 309.99
2

Mini Chestnut 2 Drawer Drum Chest

Mini Chestnut 2 Drawer Drum Chest

This cute mini round 2-drawer country-style drum chest is made from 100% solid mango wood and has a fine chestnut finish with shiny knobs on the drawers. The piece is perfect for storing small items like keys, and loose change and has space on top for displaying photos, ornaments, and collectibles. This product can be used as either a bedside table, an end table, or an occasional table. This petite product is a part of Recession Collection. Dimensions (mm) : 320D 400H 320W 320D 400H 320W

GBP 299.99
1

Mini Curved Grey Washed Bedside with Open Slot

Mini Curved Grey Washed Bedside with Open Slot

The mini version of our famous curved bedside tables, this small but handy bedside makes a perfect stand for nibbles, drinks, or a lamp. It will prove handy all over your home and is made from 100% solid mango wood in a lovely grey-washed finish. It has curved edges which will fit into any home/living space. It also comes with 1 drawer which has a shiny brass knob and 4 Nordic style legs. This petite product is a part of Recession Collection. Dimensions (mm) : 300D 550H 300W 300D 550H 300W

GBP 309.99
1

Mini Oak-ish Wall Mounted Bedside with Open Slot

Mini Oak-ish Wall Mounted Bedside with Open Slot

Inspired by our curved range, this minimalistic mini wall-mounted unit has been constructed from 100% solid mango wood in a oak-ish finish and features 1 drawer and 1 open slot. This piece is perfect for storing any bits and pieces you wish to keep close by before bedtime. Its neat and clean design can easily be mounted on the wall without the fuss of any legs. Caution! Do not sit on the unit. This petite product is part of Recession Collection. Dimensions (mm) : 250D 250H 300W 250D 250H 300W

GBP 229.99
1

Bluedry Mini Jet Hand Dryer White - HD-BD1015W

Bluedry Mini Jet Hand Dryer White - HD-BD1015W

The Bluedry Mini Jet Hand Dryer is one of the most energy efficient models on the market. With a powerful motor, users' hands are dried within 10 seconds to combine minimal energy use with customer satisfaction. The heating element can be set to on or off, offering to dry hands with a heated airflow (1.35kw) or using room temperature air with the element off (550w) to further reduce the energy use. The modern design and robustness make it suitable for high footfall areas. The Anti-Bacterial Air Filter ensures any bacteria or viruses are captured before the air is dispensed onto the users' hands, providing a clean and hygienic airflow on every single hand dry. When the hand dryer is operational, the blue LED light helps to guide the user the optimum positioning for the quickest, most efficient hand drying experience. Manufactured from grade 304 stainless steel Fitted with Anti-Bacterial Air Filter Power 550w/1.35kw Protection Level: IPX1 Motor Type: Brush 25, 000 rpm Air speed: 60 metres per second Sensor Range: 50-150mm Blue LED light guide to the airflow Dimensions: Height 268 x Width 240 x Depth 176mm Colour: White

GBP 234.99
1

Bluedry Mini Jet Hand Dryer Brushed Stainless Steel - HD-BD1015BS

Bluedry Mini Jet Hand Dryer Brushed Stainless Steel - HD-BD1015BS

The Bluedry Mini Jet Hand Dryer is one of the most energy efficient models on the market. With a powerful motor, users' hands are dried within 10 seconds to combine minimal energy use with customer satisfaction. The heating element can be set to on or off, offering to dry hands with a heated airflow (1.35kw) or using room temperature air with the element off (550w) to further reduce the energy use. The modern design and robustness make it suitable for high footfall areas. The Anti-Bacterial Air Filter ensures any bacteria or viruses are captured before the air is dispensed onto the users' hands, providing a clean and hygienic airflow on every single hand dry. When the hand dryer is operational, the blue LED light helps to guide the user the optimum positioning for the quickest, most efficient hand drying experience. Manufactured from grade 304 stainless steel Fitted with Anti-Bacterial Air Filter Power 550w/1.35kw Protection Level: IPX2 Motor Type: Brush 25, 000 rpm Air speed: 60 metres per second Sensor Range: 50-150mm Blue LED light guide to the airflow Dimensions: Height 268mm x Width 240mm x Depth 176mm Colour: Brushed stainless steel

GBP 249.99
1

3000P Convac Mini Vacuum Cleaner

3000P Convac Mini Vacuum Cleaner

Compact Engineers Vacuum Cleaner A compact, mains powered service engineers' vacuum cleaner designed for 240V a.c. operation The powerful 800W motor makes this cleaner ideal for servicing copiers and other office equipment. Supplied complete with hose, crevice tool, rubber flexible hose and flexible tube with brush attachment. A pack of 10 yellow filter bags. Manufactured to BS5415, IEC335-2.69 and VDE0700. Collects colour toner powder. Tools stow neatly into the lid compartment. Warning light indicates when filter bag is full. Thermal protection prevents overheating, Cut out 90-100C. Airflow is 34 L/min. Supplied with 3m of mains lead fitted with moulded plug (Fitted 5A fuse)

GBP 399.99
1

M30X3.50MM Chaser Die 32M M D/HD Type S20

M30X3.50MM Chaser Die 32M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 209.99
1

M24X3.00MM Chaser Die 38M M D/HD Type S20

M24X3.00MM Chaser Die 38M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 249.99
1

M20X2.50MM Chaser Die 32M M D/HD Type S20

M20X2.50MM Chaser Die 32M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 209.99
1

M24X3.00MM Chaser Die 32M M D/HD Type S20

M24X3.00MM Chaser Die 32M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 209.99
1

M16X2.00MM Chaser Die 32M M D/HD Type S20

M16X2.00MM Chaser Die 32M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 209.99
1

M30X3.50MM Chaser Die 38M M D/HD Type S20

M30X3.50MM Chaser Die 38M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 249.99
1

M36X4.00MM Chaser Die 38M M D/HD Type S20

M36X4.00MM Chaser Die 38M M D/HD Type S20

Cutting takes place only on the throat and the first full tooth; the remaining threads are above centre height and act as a nut, ensuring accurate pitch. Ideal for batch work or continuous production of threaded steel bar. Coventry dies are not interchangeable. An original set of new dies must always be used together. When taken from the diehead the set of dies should be retained in its box until required again. THROAT ANGLES: 20 for general work and soft steels - supplied as standard. 33 'B' type for cutting brass, available on request. GRINDING DIES: Only two angles are ground on Coventry dies, the throat angle and the rake angle and in the particular case of Holozone dies only the throat angle is ground. All dies in a set must be ground on the throat at the same time and since they cannot be accurately ground by hand, a die grinding fixture must be used. MARKING & MATERIALS: Each die is marked with diameter, pitch, type of die and gauge number. Non-standard or special dies are marked with an SD number which should be quoted when re-ordering. When a set of dies has been re-ground several times by grinding the throat angle, the height of the cutting edge rises above centre. This condition must be rectified by grinding the rake angle until the die height is correct according to the number shown on the die.

GBP 269.99
1