377 results (0,15489 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Apollo 45682-860APO Black XPERT Universal Address Card Pack of 10

Apollo 45682-860APO Black XPERT Universal Address Card Pack of 10

Apollo 45682-860APO Black XPERT Universal Address Card Pack of 10The Universal XPERT Address Card has been designed to allow the same card to be used on both XPERT 7 XPERT 8 bases.AddressingTo set an address using the XPERT Universal Address Card you have to remove the pips using a screwdriver. The pips are designated with numbers. Each removed pip is added together to provide the final address.Key FeaturesAddress pips have additional lead-in for a higher toleranceSimplifies and speeds up installation and commissioningAddress remains the same no matter how often the detectors are replacedIncludes 128th pip for CoreProtocol systems

GBP 4.06
1

Apollo Blank XPert Card for XPander Wireless Range -Red 29600-399

Apollo Blank XPert Card for XPander Wireless Range -Red 29600-399

Apollo Blank XPert Card for XPander Wireless Range RedSpare singular blank XPERT card in red for the XPander range. XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop.XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Brand Featuresmodern styling loop-powered interface operating on 868MHz wireless addresses seen by control panel as normal addresses radio base with wireless circuitry and battery compartment chamber designed to inhibit dirt penetration and thus reduce false alarms automatic drift compensation with DirtAlert warning algorithms for transient alarm rejection FasTest reduces time taken to test detectors remote test facility 3-5 years battery lifeProduct InformationAddress card supplied with all bases. Using a coding guide pips are removed to set the address of the inserted device.Key FeaturesSimplifies and speeds up installation and commissioningAddress remains the same no matter how often detectors are replacedUses patented proven technologyFlexibility to create any address

GBP 0.24
1

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413

Apollo Blank XPert Card for XPander Wireless Range - White 29600-413The 29600-413 is a spare singular blank XPERT card in white which has been designed for use with the XPander range. XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop.XPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesSimplifies and speeds up installation and commissioningAddress remains the same no matter how often detectors are replacedUses patented proven technologyFlexibility to create any address

GBP 0.20
1

Apollo Discovery Marine Standard Mounting Base 45681-210MAR

Apollo Discovery Marine Standard Mounting Base 45681-210MAR

Apollo Discovery Marine Standard Mounting Base 45681-210MARAll detectors in the Discovery Marine range are for use with the Marine Mounting Base. The mounting base is a low insertion force base with stainless steel contacts for the detector terminals. XPERT 7 Cards are supplied with all Discovery bases.OperationUniversal address cards known as XPERT cards are supplied with all bases. Consult the coding guide in the installation instructions to determine which pips are to be removed from the card to give the correct address. Lay the card on a flat surface pips down insert a screwdriver into the slot on the reverse of the pip to be removed and give a firm twist.When the card is coded insert it into the slot in the side of the appropriate base making sure that the card locks itself into place. As a detector is inserted into the base the remaining pips operate the address buttons on the detector and the detector electronics reads the address.Key FeaturesXPERT 7 Card addressingOne-way fitLocking feature to prevent unauthorised removal

GBP 3.84
1

Aritech ACT725-37 HID Proxcard II - Sitecode 37

Aritech ACT725-37 HID Proxcard II - Sitecode 37

Aritech ACT725-37 HID Proxcard II - Sitecode 37The ProxCard II Proximity access card incorporates radio frequency identification electronics into a thin durable polycarbonate package approximately the size of a standard credit card. It is thin and flexible enough to be carried in a wallet or on a strap clip.ProxCard II cards are easily customized with multicoloured graphics. With the application of self-adhesive photo pouch or PVC overlay the ProxCard II card is compatible with most photo ID systems.Key FeaturesOffers universal compatibility with all HID proximity readersProvides durable packaging and consistent read rangeProvides an external number for easy identification and controlHID standard 32-bit configurationA PVC overlay allows for on-site photo ID using most direct image printers

GBP 3.79
1

Aritech DB702 Dx700 Series Conventional Point Detector Base - 10cm

Aritech DB702 Dx700 Series Conventional Point Detector Base - 10cm

Aritech DB702 Dx700 Series Conventional Point Detector Base - 10cmThe Aritech DB702 is a conventional fire detector base used for all 700 series conventional fire detectors. It includes a normally closed continuity switch to allow for easy cable testing during installation. Inserting a detector into the base opens the continuity switch in the base to allow for standard open circuit monitoring. A locking mechanism implementation in conjunction with the detector allows for the detector to be safeguarded against unauthorized removal.Key FeaturesOne way only fitLocking mechanism providedInsert detectors without force

GBP 3.86
1

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APO

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APO

Apollo Soteria XPERT 8 Intelligent Mounting Base SA5000-200APOAll detectors in the Soteria XP95 and Discovery range fit into the XPERT 8 Intelligent Mounting Base.The base has a wide interior diameter for ease of access to cables and terminals. The E-Z Fit feature allows you to fit the base screws place the XPERT 8 Intelligent Mounting Base over the screws slide it into place and tighten the screws.The detector requires a clockwise rotation into the base for fitting. Additionally the detector can be locked into the base for increased security by a grub-screw using a 1.5mm hexagonal driver.The XPERT 8 card part number 38532-064 supplied with the base has pre-punched pips to remove to set the address. Refer to the Coding Guide for details on how to set the address.Backwards CompatibilitySoteria detectors have been designed to operate on XP95 and Discovery loops. This allows for Soteria detectors and bases to operate on existing systems and for Soteria detectors to operate on XP95 and Discovery bases XPERT 7 Intelligent Mounting Base. It should be noted that not all features of Soteria will be available when used with XP95 or Discovery fire control panels. If Soteria detectors are used with XP95 fire control panels incorporating drift compensation algorithms these must be disabled when communicating with Soteria devices.When Soteria detectors are used with an XPERT 7 Intelligent Mounting Base on a CoreProtocol system Soteria devices will have a 128 address offset due to only 7 address pips being available on the XPERT 7 card. For example an XPERT 7 card set at 32 will address as 160 on CoreProtocol with Soteria detectors.Key FeaturesCompatibility with Soteria XP95 and Discovery detectorsIsolated and Non-isolated devices supportedIsolated wiper - maintains loop connectivity during temporary removal of devicesXPERT 8 card for Core-ProtocolE-Z Fit allows for simple mounting of the detector base after wiringKeyed to accept only addressable devicesBase mark allows for LED detector alignmentPlease Note XPERT 8 card increase the address capacity to 254 when using Soteria detector and Core-Protocol enabled fire control panel.

GBP 2.64
1

Apollo XP95 Intelligent Mounting Base 45681-210APO

Apollo XP95 Intelligent Mounting Base 45681-210APO

Apollo XP95 Mounting Base - 45681-210APOAll detectors in the Discovery range fit the IntelligentMounting Base. The Mounting Base is a low insertion force base with stainless steel contacts for the detector terminals. XPERT cards are supplied with all bases.Universal address cards known as XPERT cards are supplied with all bases. Consult the coding guide in the installation instructions to determine which pips are to be removed from the card to give the correct address.Lay the card on a flat surface pips down insert a screwdriver into the slot on the reverse of the pip to be removed and give a firm twist. When the card is coded insert it into the slot in the side of the appropriate base making sure that the card locks itself into place. As a detector is inserted into the base the remaining pips operate the address buttons on the detector and the detector electronics reads the address.OperatingAn earth connection is not required for either safety or correct operation of detectors. The ground earth terminal is isolated and is provided for tidy termination of grounded conductors or cable screens and to maintain earth continuity where necessary. All terminals are marked according to their function.Bases have a wide interior diameter for ease of access to cables and terminals and there are two slots for fixing screws. The slots enable two fixing screws to be located at a spacing of 51mm to 69mm. Detectors fit into bases one way only without snagging and require clockwise rotation without push force to be plugged in.Key Features XPERT AddressingOne way fit of detectorLocking feature to prevent unauthorised detector removal

GBP 2.50
1

Aritech DB950 950990 Series Mounting Base

Aritech DB950 950990 Series Mounting Base

Aritech DB950 950990 Series Mounting BaseThe DB950 is an addressable fire detector base including a passsive address card. It is designed to allow the detector to be fitted without the need for any force. It has a one-way only fit. A unique patented addressing method provides simple user-friendly and accurate identification of detector location whereby a coded card inserted in the base is read by any detector as it is plugged in.VariantsAs an alternative this detector base is also available in BLACK with the same features DB950B.Key FeaturesPassive base addressElectronic free baseProgrammable slide-in address cardCompatible with 950 and 990 series detectorsFull line device line consisting of ionisation optical temperature multi sensors manual call points and multiple IO unitsAesthetic designEN54 BOSEC VdS and CNBOP approvedApollo equivalent 45681-210

GBP 3.41
1

Vimpex 8503100 Installation Accessory for Deep Base

Vimpex 8503100 Installation Accessory for Deep Base

Vimpex 8503100 Installation Accessory for Deep BaseThe 8503100 wall fixing clip fits as a mounting collar designed to be fit around the deep base of the Banshee Excel sounders and sounder beacon units. The clip helps to retain the IP66 weatherproof rating of the deep base fittings as it allows for units to be wall mounted without the need for holes to be drilled through.The 8503100 is ideal for external applications and harsh environments.Key FeaturesInstallation accessory for deep base sounder and sounder beacon unitsBlack wall fixing clipRemoves the need for holes to be drilled throughFits as a mounting collar around the deep baseDesigned for use with Banshee Excel sounders Banshee Excel Lite sounder with Xenon Beacon and Banshee Excel Lite sounder with LED beacon

GBP 2.00
1