82 results (0,13278 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Carrier 9-30855-65 EN 54-4 approved 24 V 3 A 2.6 A Intelligent Power Supply A

Carrier 9-30855-65 EN 54-4 approved 24 V 3 A 2.6 A Intelligent Power Supply A

Carrier 9-30855-65 EN 54-4 approved 24 V 3 A 2.6 A Intelligent Power Supply AThe 9-30855-65 is a fully featured 24 V EN54-4 approved power supply ideal for use in fire system applications. The output current is split between the load and charging the batteries. It features intelligent battery charging monitoring and signaling while providing deep discharge protection to prevent premature battery failure when operating from standby for extended periods.

GBP 692.98
1

Kidde Airsense Wire Burn Test Rig 9-30051

Kidde Airsense Wire Burn Test Rig 9-30051

Kidde Airsense Wire Burn Test Rig 9-30051The unit incorporates a switched 230 volts A.C. input feeding the primary coil of a 200 VA transformer. The transformer has two 6 volt A.C. outputs that are connected across three output terminals. The two outer terminals are the individual 6 volt A.C. outputs and the centre terminal is a common return. This equipment is fitted to a die-cast metal enclosure that is connected to earth. The 230 volts A.C. supply plug is fitted with a 3.0 Amp fuse.Key FeaturesBS 6266 1992. Appendix A. Procedures A.3 and A.4British Telecom WNPCPG 57200 1998 Section 4.1. Formerly FP1063.4 Issue 8 Ultra-high sensitivity. Very high sensitivity.

GBP 1015.68
1

Kidde AirSense Stratos Command Module in Steel Enclosure 9-30709

Kidde AirSense Stratos Command Module in Steel Enclosure 9-30709

Kidde AirSense Stratos Command Module in Steel Enclosure 9-30709AirSense Stratos Command Module provides a single location display control and interfacing option for systems of up to 127 detectors. Command Module allows global programming of all detector functions simultaneously.The integral bar graph automatically displays the status of the detector with the highest alarm level to identify potential problem areas. The PIN protected programmer enables global entry of all detector settings to significantly reduce commissioning time.Key FeaturesRS485 communications built in as standard for networking and remote communicationsNetwork control of 127 detectorsBuilt in Short Isolators for optimum reliabilityApplicationsData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor rooms

GBP 1852.80
1

Kidde Airsense Air Heat Box 9-30422

Kidde Airsense Air Heat Box 9-30422

Kidde Airsense Air Heat Box 9-30422The Stratos range of High Sensitivity Aspirating Smoke Detectors are suitable for installation within an area only if the ambient temperature is expected to be above 0C the minimum operating temperature of a Stratos detector is typically -10C check the specification of the particular detector in question. Where the air temperature in the protected area is consistently below this temperature it is imperative that the detector is mounted outside the protected area in an environment where the temperature meets that specified for the detector.However the sampled air from the protected area must be conditioned before it is passed into the detector. The Air Heater Box is designed to raise the temperature of the air drawn from a very cold environment by passing it across a heating element before it passes into the detector. In this manner the problem of condensation on sampling pipework external to the protected area is minimised. Warming the air sample will also ensure the components of the detector operate within the specified temperature tolerances and it reduces the possibility of surface condensation.

GBP 1192.28
1

Kidde Airsense SenseNET Software with License Dongle 9-30250

Kidde Airsense SenseNET Software with License Dongle 9-30250

Kidde Airsense SenseNET Software with License Dongle 9-30250SenseNET is a Windows based program that provides central management and monitoring of up to 127 detectors on a fault tolerant communications loop with extensive error checking and correction for the utmost in reliability. For large campus type facilities up to 16 loops of 127 detectors per loop can be efficiently monitored.The ability of SenseNET to produce site maps warning sounds and provide spoken instruction messages which may be unique to each detector is highly beneficial. Detectors may also be grouped together in zones with an associated zone map allowing alarms and faults to be quickly and easily located.Applications used inData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor roomsKey FeaturesManages all devices centrallyManages 16 x loops of 127 detectors via Command ModulesReal-time Indication of alarms identifiable sound fifesUser definable sound files for alarm and fault conditionsDisplays graphical maps with specific instructions4 levels of password protected accessFull system diagnosticsDisplay full system status or historical Information at any time

GBP 1393.28
1

Kidde Airsense 9-30855-38 EN 54-4 Approved 24 V 4 A 1.5 A Intelligent Power Supply

Kidde Airsense 9-30855-38 EN 54-4 Approved 24 V 4 A 1.5 A Intelligent Power Supply

Kidde Airsense 9-30855-38 EN 54-4 Approved 24 V 4 A 1.5 A Intelligent Power SupplyThe 9-30852-38 is a fully featured 24V EN54-4 approved power supply ideal for use in fire system applications. The output current is split between the load and charging the batteries. It features intelligent battery charging monitoring and signalling while providing deep discharge protection to prevent premature battery failure when operating from standby for extended periods.The power supply is supplied in a self-contained wall mounting box that can also house 38 Ah batteries not included. Selection of the battery size is easy with the use of a jumper. Similarly a jumper is used to select between dual-path or two individual outputs.With this feature mission critical applications can be powered ensuring redundancy in the supply of 24 V to the load.On the front of the unit 6 LEDs indicated the status of the power supply. To aid with the interpretation of the meaning of the LEDs a legend is used on the front of the unit. Additionally there is also a diagnostics LED that with different flash patterns indicated even more detailed information.A potential-free contact is used to signal faults due to output failure battery fault charger fault or internal fault. A second potential-free contact signals the loss of mains power.Key FeaturesProviding deep discharge protectionIntelligent battery charging monitoring and signallingDiagnostics LEDs on front of housingExternal housing for 38Ah batteriesDual load connection terminals2x Relay outputs

GBP 499.93
1

Kidde AirSense Stratos HSSD 2 Detector in Steel Enclosure 9-30706

Kidde AirSense Stratos HSSD 2 Detector in Steel Enclosure 9-30706

Kidde AirSense Stratos HSSD 2 Detector in Steel Enclosure 9-30706Stratos HSSD2 is designed to provide very high sensitivity smoke detection ensuring the very earliest warning of incipient fire with minimum rate of nuisance alarms. ClassiFire Perceptive Artificial Intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup.This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area. Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems. Command module available for central monitoring and display.Typical ApplicationsData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor roomsKey FeaturesHigh sensitivity provided by laser based forward light scatter for reliable early warningCombined sampling pipe up to 200m in length still airUnique ClassiFire Perceptive Artificial Intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and dust separation system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination systemRS485 communications built in as standard for networking and remote communicationsLarge area aspirating smoke detector up to 2000m2 coverageCPR LPCB VdS NF CSIRO UL FM approved

GBP 2231.89
1

Kidde Airsense Micra 10 Single Pipe Aspiration Smoke Detector 9-30725

Kidde Airsense Micra 10 Single Pipe Aspiration Smoke Detector 9-30725

Kidde Airsense Micra 10 Single Pipe Aspiration Smoke Detector 9-30725The AirSense Micra 10 is designed to provide very high sensitivity smoke detection in a small package. ClassiFire Perceptive Artificial Intelligence ensures that the detector operates at optimum sensitivity for the protected environment without the need for complex setup. This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.The detector is designed to fit into a Docking Station. All sampling pipes and cables are connected to the Docking Station as a first fix operation leaving the detector to be fitted during the final commissioning phase if required. This ensures that detectors are less likely to be damaged during the installation. Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems.ApplicationsData storage unitsPrison cellsPlant roomsAir conditioning unitsEquipment racksComputer roomsAir duct protectionHeritage property protectionCritical equipmentAnti-smoking enforcementMotor roomsKey FeaturesUltra-small low-cost aspirating smoke detector for easy and discreet installationHigh sensitivity provided by laser based forward light scatter for reliable early warningSingle sampling pipe up to 50m in length still airUnique ClassiFire Perceptive Artificial Intelligence system that dynamically adjusts the detectors operating parameters allowing for day to day changes in the protected environment and dust separation system contaminationUnwanted alarms from dust are avoided using patented Dual Technology LDD 3D3 Laser Dust Discrimination and elimination system

GBP 888.07
1

Kidde AirSense Stratos ModuLaser Detector Module 9-30783

Kidde AirSense Stratos ModuLaser Detector Module 9-30783

Kidde AirSense Stratos ModuLaser Detector Module 9-30783ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 856.82
1

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display Module

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display Module

Kidde 9-30780-KID Kidde Senator Modulaser Minimum Display ModuleModuLaser is a scalable aspirating smoke detection solution thatmakes installation easier maintenance quicker and takes applicationsfurther than traditional air sampling detectors. Two basic module typescomprise the ModuLaser solution a display module and a detectormodule. Each detector module can accommodate up to 250 meterscombined sampling pipe. Display modules and detector modulescommunicate by RS-485 interconnections.Display modules are available in three configurations Standard withTFT colour display status LEDs and navigation buttons Minimum withonly status LEDs and Command which is similar to the Standard butwith the added functionality to control various modules overSenseNET. The Minimum and Standard Display Modules can eachsupport up to 8 detector modules while the Command Display Modulecan support up to 127 modules across the SenseNET network.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see color TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 487.51
1

Testifire 9001-001 Smoke and Heat Detector Test and Removal Kit - 9 Metres 30 ft

Testifire 9001-001 Smoke and Heat Detector Test and Removal Kit - 9 Metres 30 ft

Testifire 9001-001 Smoke and Heat Detector Test and Removal Kit - 9 Metres 30 ftNow Including High Capacity Battery BatonsTestifire 1000 Series is the worlds first multi-stimulus detector tester for smoke heat and multi-stimulus detectors. Both smoke and heat stimuli are created in a single test unit and delivered individually or - for the first time - simultaneously in whichever combination are required.Testifire does this without using pressurised cans of gas or other hazardous goods. Stimuli Smoke and Heat are generated at the time of test using safe and patented processes fuelled by replaceable capsules.The new SOLO770 Battery Baton is a higher capacity product 3000mAh. It allows greater efficiency both in the field and on-site as it gives more tests per battery for the same charge time as before but provided by the new SOLO727 Battery Charger.The SOLO727 charger has also been improved and while it provides the same functionality as before it is now capable of enabling fast charging of the new higher capacity battery batons from both mains power and in-vehicle outlets.Features BenefitsTesting with one tool is faster and more productiveLess tools and equipment to carry aroundAllows testing and removal of detectors up to 9 metres 30 ft in heightCombined stimuli delivers quicker activation times for combination detectorsUnique Clearing Cycle provides rapid detector reset with no repeat alarmsTest times reduced by as much as 66 saving labourFully reverse compatible with the Solo range of poles battery batons and chargers.Ideal in any application Land Air and MarineA must have addition to any Professional Engineers Tool SuiteReduced carriage and shipping costs - no pressurised cans of gasReduced Test Stimuli Re-stocking and freight costs - no pressurised cans of gasTestifire 9001 - 001 Smoke and Heat Detector Testing and Removal Kit Includes1 x Testifire 1000-001 Head Unit inside the 1001-001 box it will also include1 x TS3-001 Smoke Capsule 1 x Solo 770-001 Battery Baton option to buy second baton in the drop-down box and 1 x Solo 727-001 Multi Voltage Fast Charger1 x Solo 100-001 Fibreglass Telescopic Access Pole 4.5 metres 15 ft3 x Solo 101-001 Fibreglass Extension Pole 1.13 metres 4 ft1 x Solo 200-001 Universal Detector Removal Tool1 x Solo 610-001 Protective Carrying Storage Bag

GBP 2511.41
1

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780

Kidde AirSense Stratos ModuLaser Minimum Display Module 9-30780ModuLaser is a scalable aspirating smoke detection solution that makes installation easier maintenance quicker and takes applications further than traditional air sampling detectors. Two basic module types comprise the ModuLaser solution a display module and a detector module. Each detector module can accommodate up to 250 meters combined sampling pipe. Display modules and detector modules communicate by RS-485 interconnections.Display modules are available in three configurations Standard with TFT colour display status LEDs and navigation buttons Minimum with only status LEDs and Command which is similar to the Standard but with the added functionality to control various modules over SenseNET. The Minimum and Standard Display Modules can each support up to 8 detector modules while the Command Display Module can support up to 127 modules across the SenetNET network.Thanks to advanced features that make it virtually impervious to dust and dirt ModuLaser is ideal for use in hostile environments that would disable other kinds of smoke detectors. Forward scattering optical detection adds early warning capability without the risk of nuisance alarms normally associated with high sensitivity smoke detection while exclusive environmental compensation technology adds a high degree of reliability to an already solid detection solution.Key FeaturesModular Design Separate centrally-controllable detector modules allow efficient piping and discrete zones with no overlap.Zoned aspirating smoke detection Individual detector modules provide detection for individual areas or zones specific zone alarm information can be transmitted to the main fire alarm panel via a common APIC address card in the display module or through dedicated alarm relays within each detector module.Simplified installation Ingenious docking station design allows detectors to be easily connected together as a group. Sensitive electronics are easily removed to ensure they will not be damaged during first fix installation. Aspirating pipework and cable entries can easily be made into either the top or the bottom of the unit.Intuitive user interface Bright easy-to-see colour TFT display and universal navigation and control buttons take the guesswork out of programming and diagnostics.Easy pipe connection The quick fit pipe adaptor system locks down securely yet leaves plenty of room for easy pipe connection and removal.Quick location of smoke Each detector module is self-contained which means no delays in determining in which zone sampling pipe smoke is present.

GBP 948.44
1

Testifire 9201-001 Smoke Heat and CO Detector Test and Removal Kit - 9 Metres 30 ft

Testifire 9201-001 Smoke Heat and CO Detector Test and Removal Kit - 9 Metres 30 ft

Testifire 9201-001 Smoke Heat and CO Detector Test and Removal Kit - 9 Metres 30 ftNow Including High Capacity Battery BatonsTestifire 2000 Series is the worlds first multi-stimulus detector tester for smoke heat and CO fire detectors. Smoke heat and CO stimuli are created in a single test unit and delivered individually or - for the first time - simultaneously in whichever combination are required.Testifire does this without using pressurised cans of gas or other hazardous goods. Stimuli Smoke Heat and CO are generated at the time of test using safe and patented processes fuelled by replaceable capsules.The new SOLO770 Battery Baton is a higher capacity product 3000mAh. It allows greater efficiency both in the field and on site as it gives more tests per battery for the same charge time as before but provided by the new SOLO727 Battery Charger.The SOLO727 charger has also been improved and while it provides the same functionality as before it is now capable of enabling fast charging of the new higher capacity battery batons from both mains power and in-vehicle outlets.Features BenefitsTesting with one tool is faster and more productiveLess tools and equipment to carry aroundAllows testing and removal of detectors up to 9 metres 30 ft in heightCombined stimuli delivers quicker activation times for combination detectorsUnique Clearing Cycle provides rapid detector reset with no repeat alarmsTest times reduced by as much as 66 saving labourFully reverse compatible with the Solo range of poles battery batons and chargers.Ideal in any application Land Air and MarineA must have addition to any Professional Engineers Tool SuiteReduced carriage and shipping costs - no pressurised cans of gasReduced Test Stimuli Re-stocking and freight costs - no pressurised cans of gasTestifire 9201 - 001 Smoke Heat and CO Detector Testing and Removal Kit Includes1 x Testifire 2000-001 Head Unit inside the 2001-001 box it will also include 1 x TS3-001 Smoke Capsule 1 x TC3-001 CO Capsule 1 x Solo 770-001 Battery Baton option to buy second baton in the drop-down box and 1 x Solo 727-001 Multi Voltage Fast Charger1 x Solo 100-001 Fibreglass Telescopic Access Pole 4.5 metres 15 ft3 x Solo 101-001 Fibreglass Extension Pole 1.13 metres 4 ft1 x Solo 200-001 Universal Detector Removal Tool1 x Solo 610-001 Protective Carrying Storage Bag

GBP 4123.44
1