154 results (0,12732 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Aritech ACT455 Mifare EV2 PVC Card Empty Pack Of 25 For Use With ATS Programmer No SW

Aritech ACT455 Mifare EV2 PVC Card Empty Pack Of 25 For Use With ATS Programmer No SW

Aritech ACT455 Mifare EV2 PVC Card Empty Pack Of 25 For Use With ATS Programmer No SWThe ISO card in white color offers a robust solution for a secure environment where card data is protected with Mifare Desfire EV1 or EV2 encryption. The card offers a 2 kB application memory. It can be used in secure mode with ATS118x range readers and ATS1136 keypad. It can also provide for Mifare 7-byte CSN.Key FeaturesISO card modelCard data can be secured by Mifare Desfire EV1 or EV2Mifare Desfire EV2 card with 2 kB application memoryPrinted serial numberCan be programmed with Secure Programmer

GBP 97.63
1

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications CardAn optional system expansion device for use with XFP 12 Loop 32 Zone fire panels. Allowsthe connection of up to eight XFP Repeaters or eight XFP Main panels any mix on an RS485 network. One AFP711 card required per networked Main XFP 12 Loop 32 Zone panel note that XFP510-16 and XFP510-32 repeaters include a network driver card as standard.The AFP711 is NOT compatible with XFP Single Loop 16 Zone panels which require a CFP761 card for networking.Key network protocol features when used for interconnecting XFP main panelsCan be used to connect up to 8 XFP main panels any mix over a two-wire RS485 network of up to 1KM in length.Each networked XFP can be programmed to accept Fires Faults and Control actions such as Silence Alarm Sounders and Control Panel Resets from other panels.Each XFP will accept Disablement commands for zones sounders and output sets from other panels.All panels monitored for network wiring faults.Fires and faults on remote panels are displayed on local panels including the point description.CEs can be programmed into local panels dependent on which remote panel is in alarm.The network supports the programming of site data into remote panels from a PC at a local panel.Time and date is common to all panels.All networked main panels require a network communication card.It is not possible to mix XFP main panels and XFP repeaters on the same network.Key network protocol features when used for connecting XFP repeatersCan be used to connect up to 8 XFP repeaters any mix to one XFP main panel.Up to 500m of cable may be fitted to an XFP two-wire repeater network.Each XFP repeater offers all the functions and controls of an XFP main panel.The XFP main panel must have a network communication card fitted.It is not possible to mix XFP main panels and XFP repeaters on the same network.

GBP 114.65
1

Aritech ATS1495 Dual ISO Card - With HiTag 2 And Secure Mifare Pack Of 10

Aritech ATS1495 Dual ISO Card - With HiTag 2 And Secure Mifare Pack Of 10

Aritech ATS1495 Dual ISO Card - With HiTag 2 And Secure Mifare Pack Of 10The ISO card in white color offers a robust solution for a secure environment where card data is protected with Mifare Desfire EV2 encryption. It can be used in secure mode with ATS118x range readers and ATS1136 keypad.When used on other Mifare Readers the standard Mifare 7-byte CSN is provided instead of the secure card data.In addition the card provides for Hitag2 card serial number as supported by ATS119x reader range and ATS111x and ATS1135 keypads to allow simultaneous use of both technologies while migrating from old to new secure technologies.Key FeaturesAttractive designed keyfob in ISO card modelCard data secured by AES encryptionMifare Desfire EV2 encrypted applicationHitag2 Card Serial Number

GBP 111.00
1

Haes Comms Card for Repeater amp Network Connections TPCA05

Haes Comms Card for Repeater amp Network Connections TPCA05

Haes Comms Card for Repeater Network Connections TPCA05The Haes comms card TPCA05 allows up to eight XLEN or XL32 control panels to be networked. Any combination of panel can be used from a 2 zone to a 32 zone and in any order to provide up to 256 conventional or Twin Wire zones. The card simply plugs in on top of the main circuit board in the control panel. In addition to the eight control panels up to eight repeater panels or remote display units can also be added to the network. The remote display units are supplied with a 4 x 40 character backlit LCD and will display all system fires and faults as well as controlling Silence Reset and other functions for the entire network.The networking has been designed to be wired in a fault tolerant fail safe loop configuration from comms A to B and back to the main panel again. If replacing an older system where the existing cabling cannot be configured in a loop as above it is possible to re-programme the master panel back to legacy RS485 circuit comms monitoring. This then allows any topology of comms cabling to be utilised. The cards are also provided with six programmable switch negative outputs which can be utilised for any local switching requirements.

GBP 126.86
1

C-Tec ECU722 SigTEL Network Communication Card

C-Tec ECU722 SigTEL Network Communication Card

C-Tec ECU722 SigTEL Network Communication CardNetwork card allows up to 14 ECU-4 8 16 or 8NTs to be interlinked. To network a controller that has an optional ECU-224 desk controller fitted use an ECU723 interfacenetwork card instead.The ECU722 card transmits speech via a single wiring loop and digital data via two linear RS485 networks. The network should be connected using 4 x 2-core 1.5 mm2 enhanced fire-rated cable. Max. length of all networks is 1 km.Key FeaturesAn optional system expansion device.Allows up to 14 ECU-4 8 16 or 8NT SigTEL controllers to be interlinked.One card required per networked SigTEL controller.Allows systems of up to 224 lines 14x ECU-16controllers to be easily set-up.Any ECU-4ECU-8 or ECU-16 can take control of the system at any time by the input of a special code.Note that for networked systems that do not require multiple control points controllers without handsets are available ECU-8NT.IMPORTANT To network a controller that has an optional ECU-224 desk controller fitted use an ECU723 interfacenetwork card instead of an ECU722 the ECU723 is due for release Nov 2019.

GBP 90.65
1

Advanced Sounder Splitter Card - MXS-021

Advanced Sounder Splitter Card - MXS-021

Advanced Sounder Splitter Card - MXS-021The Mxs-021 Sounder Circuit Splitter is a peripheral unit for use with all MxPro4 range of control Panels. This additional unit takes a standard sounder circuit from either a control panel or other panel based sounder circuit controller and multiplies to provide up to 4 monitored outputs. In operation the additional outputs follow the output they are connected to. The circuits are fully monitored for open and short circuit and will take an independent supply to provide up to 1A per circuit.Key Features4 Monitored Outputs3 Year Warranty as standardUp to 1 Amp per circuitCost effective against ancillary hardwareCompatibilityThe Sounder Splitter Cardis compatible with all MxPro 4 controlpanels.LimitationsThe 4-way sounder splitter card can be supplied as a PCB only for mounting. When supplied fitted in this format the load at the outputs from the splitter will be limited to the sounder output loading of the input circuit from which it is driven.All 4 outputs on the sounder splitter card will operate in tandem and follow the output of the sounder circuit to which the card is connected.

GBP 163.18
1

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052

Advanced MxPro 10 Way Mimic Relay Card - Mxp-052The Mxp-052 is a peripheral relay card providing ten 30V DC 1A programmable relay outputs. The Mxp-052 connects directly to any of the DIL connectors of either the Network Mimic Mxp-020-100 LED Output Card or the General IO controller Mxp-045 LED Output Card units via the supplied ribbon cable.Each output follows the cause and effect programming of the mimic unit output. This can be either a simple zone output or can be an individually programmed output group rule utilising the full range of features of the Mx-40005000 systems Dynamix zoning facilities.Key FeaturesTen change-over contact outputs rated at 30V DC 1A.Up to 200 individual relay outputs fully programmable per mimic excluding LEDsTen individually programmable relay outputs per unitDIN rail or screw fixing optionsSeparate isolate input disables all outputsSeparate isolate indication outputFast instant responseProduct CodesDescriptionMXP-052Mimic driven 10-way relay output cardMXP-052-DINMimic driven 10-way relay output card in din-rail carrier

GBP 129.16
1