43 results (0,14442 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kidde Airsense Stratos Remote Display Unit 9-30802

Kidde Airsense Stratos Remote Display Unit 9-30802

Kidde Airsense Stratos Remote Display Unit 9-30802The Remote Display Unit RDU is a LED bar-graph repeater and status display which is used to remotely mimic the status of a Stratos ASD. It comes in 19 rack format that allow for multiple units to be mounted next to each other in a 19 rack or individually with the support of the 9-30817 housing.The RDU is connected onto the SenseNET bus which provide the data flow between the unit and the ASD. A bank of switches selects the detector whose display is to be repeated. The unit is powered from a 24V DC nominal power supply.The RDU provide by way of LEDs basic ok and faults indication 4 alarm levels and a bar-graph display which show the level of obscuration. The RDU can also be expanded with a relay card 9-30803 which provide relay output for the 4 alarms flags and fault indication.Key FeaturesLED status indication bar-graph display19 rack mount supportOptional relay expansion

GBP 290.11
1

Ziton 9-30437 APIC Card - Ziton Protocol

Ziton 9-30437 APIC Card - Ziton Protocol

Ziton 9-30437 APIC Card - Ziton ProtocolThe 9-30437 is an interface which can be attached directly onto the main control board of any LaserSense aspirating detector. The card plugs into the main control board inside the detector enclosure. The board enables the detector to be directly addressed and communicate with the ZP3 main control panel.Detectors are wired onto the loop using plug in terminals located on the LaserSense detector main control board. The detector and interface are easily addressed by switch settings prominently positioned on the card.The interface is recognised by the main control panel as device type HSSD and dependent upon the analogue signals received and control panel software installed will provide the following alarm conditions Fault Alert Pre-alarm Fire. Alert not displayed on ZP3 panelFor ZP control panels operating on software prior to version 3.07 confirmation of available signals should be obtained from Ziton sales department. Up to 127 sensing devices can be connected to each of the control panel loops.Key FeaturesSimple LaserSense addressing onto ZP loopRibbon cable connection no hard wiringPiggy backs onto detector main boardEase of address setting

GBP 271.74
1

Kidde Airsense Relay Input Card 9-30436

Kidde Airsense Relay Input Card 9-30436

Kidde Airsense Relay Input Card 9-30436Input Relay Cards plug into the APIC interface slot in each detector and cannot be used in conjunction with APIC Cards. An Input Relay Card provides detector inputs that may be programmed for Remote DayNight Mode Changeover Remote Reset or ClassiFire Override as well as power supply fault monitoring. ClassiFire Override is a particularly useful feature that enables the normal detector sensitivity to be reduced by a pre-programmed percentage to avoid unwanted alarms from a predictable event such as theatre stage effects or open fires in heritage buildings.Key Features4 staged normally open relay outputs.Relay contacts rated at 0.4A 24vDC.Compatible with Stratos-HSSD and Stratos-Micra detectors.Common Fault relay energised normally closed for fail safe operation.

GBP 193.76
1

Kidde 9-30852-18 EN 54-4 Approved 24 V 1.75 A 0.75 A Intelligent Power Supply

Kidde 9-30852-18 EN 54-4 Approved 24 V 1.75 A 0.75 A Intelligent Power Supply

Kidde 9-30852-18 EN 54-4 Approved 24 V 1.75 A 0.75 A Intelligent Power SupplyThe 9-30852-18 is a fully featured 24 V EN54-4 approved power supply ideal for use in fire system applications. The output current is split between the load and charging the batteries. It features intelligent battery charging monitoring and signalling while providing deep discharge protection to prevent premature battery failure when operating from standby for extended periods.On the front of the unit diagnostic LEDs indicate the status of the power supply with various flash patterns to ensure accurate diagnostics when the unit is in fault.The range is available in different size of output currents with support for various sizes of batteries.Key FeaturesApproved to EN54-4 VdS certifiedSelf-contained box houses 18 Ah batteriesDeep battery discharge protectionDiagnostics leds on front of housing2 x relay outputsDual load connection terminalsWide input voltage range

GBP 292.87
1

Kidde Airsense APIC Card Notifier Protocol 9-30433

Kidde Airsense APIC Card Notifier Protocol 9-30433

Kidde Airsense APIC Card Notifier Protocol 9-30433APIC cards plug into a connector on the main PCB provided for that purpose. To use the Notifier APIC all that is required is to plug the card into this connector using the ribbon cable attached to the interface connect loop in and loop out on the terminals on the detector PCB and set the switches to the loop address. The APIC has two distinct modes of operation single address and multi address. When the interface is set to single address mode the card is set to a single address on the Notifier loop and the detector status is read from that address.Multi address mode is used when monitoring the status of multiple detectors with consecutive addresses from a single APIC card. Multi address mode is normally only used in the Command Module. Two pairs of switches Highest and Lowest on the APIC card enable the card to either respond as a single address as it does in a detector or a range of addresses which is the way it is set up in the Command Module.To set up an APIC in a detector which only requires a single address single address mode set both pairs of switches to the required address on the Notifier loop. This sets the card to single address mode. The APIC pictured is set to single address mode at address 15.

GBP 181.16
1

Carrier 9-30855-18 EN 54-4 approved 24 V 5 A 0.7 A Intelligent Power Supply

Carrier 9-30855-18 EN 54-4 approved 24 V 5 A 0.7 A Intelligent Power Supply

Carrier 9-30855-18 EN 54-4 approved 24 V 5 A 0.7 A Intelligent Power SupplyThe 9-30855-18 is a fully featured 24 V EN54-4 approved power supply ideal for use in fire system applications. The output current is split between the load and charging the batteries. It features intelligent battery charging monitoring and signaling while providing deep discharge protection to prevent premature battery failure when operating from standby for extended periods.On the front of the unit diagnostic LEDs indicate the status of the power supply with various flash patterns to ensure accurate diagnostics when the unit is in fault.The range is available in different size of output currents with support for various sizes of batteries.Installer friendlyThe power supply is supplied in a self-contained wall mounting box that can also house 18 Ah batteries not included.Selection of the battery size is easy with the use of a jumper. Similarly a jumper is used to select between dual-path or two individual outputs. With this feature mission critical applications can be powered ensuring redundancy in the supply of 24 V to the load.On the front of the unit 6 LEDs indicated the status of the power supply. To aid with the interpretation of the meaning of the LEDs a legend is used on the front of the unit. Additionally there is also a diagnostics LED that with different flash patterns indicated even more detailed information.A potential-free contact is used to signal faults due to output failure battery fault charger fault or internal fault. A second potential-free contact signals the loss of mains power.EN 54-4 approved 24 V 5 A 0.7 A intelligent power supplyApproved to EN54-4 VdS certifiedSelf contained box houses 18 Ah batteriesDeep battery discharge protectionDiagnostics leds on front of housing2 x relay outputsDetailsApproved to EN54-4 VdS certifiedSelf contained box houses 18 Ah batteriesDeep battery discharge protectionDiagnostics leds on front of housing2 x relay outputsDual load connection terminalsWide input voltage range

GBP 357.18
1

Checkfire FX-LI-009-MCF Lithium-Ion Battery Fire Extinguisher 9 Litre

Checkfire FX-LI-009-MCF Lithium-Ion Battery Fire Extinguisher 9 Litre

Checkfire FX-LI-009-MCF Lithium-Ion Battery Fire Extinguisher 9 LitreThe LFX range has been specifically designed to tackle lithium-ion battery fires across a wide range of applications. In addition to primary fire risks the LFX fluorine-free range of fire extinguishers also protect from secondary A-class fires that have been caused by the exploding batteries.Suitable for devices up to 900Wh ratings our 9ltr LFX lithium-ion battery fire extinguishers are designed to safeguard devices such as e-scooters and e-bikes up to 900Wh making them ideal for manufacturers and rental services.Part of The Green Range this nine-litre fire extinguisher fiercely tackles the unique risks of lithium-ion battery fire. Its completely fluorine-free with NTA 8133 fire extinguisher certification that proves its reliability and effectiveness in extinguishing lithium-ion battery fires.Using a water-based agent that discharges as an endothermic foam LFX quickly breaks down the chain reaction in thermal runaway and cools the temperature of the batteries absorbing significantly more heat than water alone. It also protects from secondary A-class fires extinguishing any peripheral fires potentially caused by exploding batteries.With the Regulatory Reform Fire Safety Order 2005 now recognising that lithium-ion batteries need to be considered in all fire risk assessments in the UK there has never been a better time to stock up on this innovative solution and stay prepared.Key FeaturesSuitable for lithium-ion battery powered devices with ratings up to 900WhNTA 8133 certifiedEndothermic agent for fast heat absorptionCompletely fluorine-freeStrong base skirt for protectionTough corrosion-resistant finishCE-marked brass valve assembly with strong handlesClass-leading thick polyethylene internal liningFull range of spare parts availableEuropean manufacturerFive-year warranty

GBP 306.60
1

C-Tec FiTT EVC Line Tester

C-Tec FiTT EVC Line Tester

C-Tec FiTT EVC Line TesterThe FiTT line tester is an easy to use test set which allows you to test the wiring for a SigTEL Type A fire telephone outstation andor a SigTEL Type B disabled refuge outstation prior to its connection to an appropriate SigTEL exchange unit.The FiTT is supplied with a non-rechargeable 9 volt PP3 alkaline battery allowing approximately 28 hours use and all the test cables and connectors you need. Always replace the battery with a non-rechargeable 9 volt PP3 alkaline battery. Do not use a rechargeable battery.

GBP 329.02
1

Kidde Airsense APIC Card Apollo Protocol 9-30430

Kidde Airsense APIC Card Apollo Protocol 9-30430

Kidde Airsense APIC Card Apollo Protocol9-30430The Stratos APIC Addressable Protocol Interface Card provides a cost effective interfacing solution for Apollo loop protocol based fire detection systems. The APIC utilises the Series 90 loop protocol to ensure optimum compatibility with all Apollo based systems. Apollo XP95 and Discovery compliant systems are backwards compatible to series 90. Stratos detectors fitted with the APIC are indicated at the control panel as Optical Smoke and returns the following loop condition values.Key FeaturesMay be fitted internally to each Stratos detector on a system or if a Command Module is used a single APIC may be used in Multi Address mode in the Command Module for signaling up to 127 detectors resulting in reduced cost in large systems. Direct addressing of multiple alarm thresholds provides opportunity for earlier intervention. The card is compatible with Stratos-HSSD Stratos-Micra and Stratos-Ex detectors.

GBP 278.59
1

Kidde Airsense Stratos Pipe Stand-off Support 9-10936

Kidde Airsense Stratos Pipe Stand-off Support 9-10936

Kidde Airsense Stratos Pipe Stand-off Support9-10936The pipe stand-off support includes CLIC TOP 28 pipe clip M8 x 60mm stud and mounting bracket. The stand-off is suitable for 34 pipework and not suitable for 25mm pipework.Aspirating smoke detection system is the network of sampling pipes that actively transport air from a protected area to the detector. ABS Acrylonitrile Butadiene Styrene is a homogenous material with good chemical resistance and high impact strength. Other beneficial features are its suitability for use at low temperatures -40C and its ease of joining.

GBP 365.80
1

Solo 330 Aerosol Smoke and CO Dispenser

Solo 330 Aerosol Smoke and CO Dispenser

Solo 330 Aerosol Smoke and CO DispenserThe Solo 330 smokeCO dispenser with its injection-moulded construction and swing frame make it the ideal tool for testing virtually all types and makes of modern smoke detectors at heights of up to 9 metres Using the SOLO100-001 Pole. Ergonomically designed for optimum use with the Solo Aerosol range together offering fully controlled and efficient testing. The Solo 330 is for use when testing detectors of up to 100mm in diameter.Robust - to withstand the rigours of everyday useStrength and durability - to ensure long lifeInjection-moulded plastic design - minimises weightSpring loaded mechanism - effective areosol deliveryDispenser and diaphram contain particles - conserves aerosolAerosol spray not directed at detector - sensor not swampedTouch sensitive - ideal for suspended ceilingsUniversal - suits most detectors from normal height to 9 metresClear cup and diaphram - allows view of detector LEDInterchangeable with all other Solo Tools

GBP 346.99
1

Kentec K85001BLU BMS License Upgrade

Kentec K85001BLU BMS License Upgrade

Kentec K85001BLU BMS License UpgradeK85001BLU is a licence upgrade for the Vizulinx gateway and needs a working gateway unit to be applied. It is a software licence unlock function to activate additional Modbus BMS points within the gateway. A maximum of 9 x K85001BLU can be applied to any gateway unit.The Modbus BMS points are enumerators and therefore can be used to show all currently active events for the detection device they are mapped to. Each Modbus point can display up to 10 status flags Normal Fire Evacuate Pre-Alarm Fault Disablement test security alarm and technical alarm status for the associated device.If there is a requirement for more than 10000 Modbus BMS points then additional Vizulinx units will need to be installed on remote networked Syncro panels. It is not possible to serially connect more than one Vizulinx unit to a Syncro panel using serial data.Key FeaturesUp to 9 licence modules can be unlocked per unit10000 point maximum capacity per Vizulinx unitPoints are mapped in blocks of 250 points for each loopNon sequential loop allocation is supported i.e. Panel 1 loop 1 2 3 plus Panel 2 loop 1 1000 points

GBP 342.25
1

Zeta GSM-COM GSM Communicator

Zeta GSM-COM GSM Communicator

Zeta GSM-COM GSM CommunicatorZeta GSM communicator is an interface that allows a fire alarm panel to send a SMS text message in the event of an alarm or a fault.The communicator accepts a standard Mobile Phone SIM card and is then programmed with the alarm information phone numbers via a PC.The unit can run on any power supply between 9 24V DC.The unit has 4 inputs 2 user definable outputs.The outputs can be manually operated by dialling the GSM communicator then entering a password.

GBP 301.03
1

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with Handset

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with Handset

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with HandsetAn attractive Type Afire telephoneoutstation cw telephone-style handset. Supplied in a durable lift key lockablered steel case. Ideal for use infire telephone and stadium marshalling applications. Allows stewards and fire marshalsto communicate with a SigTEL Master Controller and vice versa. Facilitatesreliable two-way communication in a fire emergency between a permanently manned control room and key points ofasite.Key FeaturesTrue duplex speechCan be surface mounted using a T-BEZ302 bezelMeets and exceeds the requirements of BS 5839-9 when correctly installed

GBP 245.40
1

Baldwin Boxall 100W Volume Controls with Override Relay BVC100

Baldwin Boxall 100W Volume Controls with Override Relay BVC100

Baldwin Boxall 100W Volume Controls with Override Relay BVC100These volume controls are designed to attenuate the signal fed to loudspeakers driven by the 100-volt line output of a public address amplifier. The volume control is fitted into a double gang surface mounting box and can be used with any number of loudspeakers provided the load does not exceed 100 Watts. The control has 9 steps of 3dB. The knob is fully rotating. A volume restoration relay is fitted and operates in the same way as the BVC6.

GBP 219.54
1