7 results (0,13899 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda Xtralis PIP-027 Air Sampling Test Point with Cap

Vesda XtralisPIP-027Air Sampling Test Point with CapThey are designed to measure the transportation time a small quantity of smoke is introduced at the furthest point and the measurement in time is calculated from when the smoke enters the sampling point to when the ASD reacts. The maximum transport time is 120 seconds 2 minutes. Test points are the ideal solution for flexibility and convenience. They are installed at the end of the pipe run however for areas such as a lift shaft where accessibility is limited the pipe run can be brought into a riser.A key element of the VESDA system is its suction system which actively transports air from the protected area to the detector.The test point is for periodic smoke testing of the VESDA system for hard to reach areas.VESDA installations can be designed for the most complex areas using carefully selected shaped elements.The use of these shaped elements has a positive effect on the pneumatic system of the installation which translates into the unique and legendary quality of the VESDA system work in each pneumatic system.The suction installation is calculated with theASPIREprogramme.The program is used for modelling and visualization of aspiration installations class calculation in accordance with PN-EN-54-20.Please note The PIP-027 is equivalent to the REDAST025C.

GBP 7.49
1

KAC MCP1A-R-470 Red Break Glass Call Point - 470 Ohm Flush

KAC MCP1A-R-470 Red Break Glass Call Point - 470 Ohm Flush

KAC MCP1A-R-470 Red Break Glass Call Point - 470 Ohm FlushThe MCP1A-R-470 is a Red Break Glass Call Point.Installation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP indoor call point range.Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.Through new standards and legislation both break glass and resettable operating elements can now be used within a manual call point. To provide you with the greatest flex-ability the new MCP range can be configured as either a break glass or resettable unit by simply changing from one element to another. No other additional parts or alternative products need to be ordered.All MCP indoor call point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going into alarm.Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard Compliant markings only.The MCP1A product version is supplied with both a resistor and normally open clean contact electrical options.Key FeaturesColour Red470OhmUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aestheticsFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 8.75
1

Cooper Fulleon 593010FULL-0323 Combi Base 2x Deep Base White

Cooper Fulleon 593010FULL-0323 Combi Base 2x Deep Base White

Cooper Fulleon 593010FULL-0323 Combi Base 2x Deep Base WhiteThe Combi signalling units provide an extremely flexible system for the assembly of audible and visual signals that may be used in applications where different levels of warning or status need to be communicated.The foundation of the system is the Deep Base pre-assembled into linear units of 2 3 or 4 pieces. Into the assemblies the user can fit audible and visual warnings chosen from the standard ranges of Fulleon RoLP sounders Solex Xenon beacons and Solista Maxi LED beacons.The RoLP and RoLP Maxi allow the user to choose from 32 alarm tones and outputs in excess of 107dBA.The Solex Xenon beacons are available with three levels of light output and in five colours the Solista LED beacons again offer five colours and additionally three user selectable modes of operation steady single flash and double flash.LED beacons also are inherently robust and have extremely long operating lifetimes important where access for maintenance may be limited. Supply voltages from 9 to 60Vdc and 110 to 230Vac are available.Please see data sheets for the particular devices for full specification.Key Features Two three- or four-way assemblies to suit the status levels required.Two stage alarm sounders with 32 tones avoids conflicts with other alarm signalsFive colours available with both Xenon and LED light sources to suit most visual requirementsChoice of three light outputs for the Xenon beacons to suit the visibility levels requiredThree user selectable flash modes from the LED beacons allows clear differentiation between signals.Audible and visual elements can be locked into the Combi bases for added securityBases are available in either red or white to suit the applicationStandard voltage range 9 to 30Vdc. 60Vdc also available and will suit most commonly available DC suppliesAC mains operation from 110 to 230Vac with Combi Power module allows operation from AC supplies with the need for adjustment.

GBP 5.09
1

Cooper Fulleon 593004FULL-0034 Combi Base 2 x Deep Base Red

Cooper Fulleon 593004FULL-0034 Combi Base 2 x Deep Base Red

Cooper Fulleon 593004FULL-0034 Combi Base 2 x Deep Base RedThe Combi signalling units provide an extremely flexible system for the assembly of audible and visual signals that may be used in applications where different levels of warning or status need to be communicated.The foundation of the system is the Deep Base pre-assembled into linear units of 2 3 or 4 pieces. Into the assemblies the user can fit audible and visual warnings chosen from the standard ranges of Fulleon RoLP sounders Solex Xenon beacons and Solista Maxi LED beacons.The RoLP and RoLP Maxi allow the user to choose from 32 alarm tones and outputs in excess of 107dBA.The Solex Xenon beacons are available with three levels of light output and in five colours the Solista LED beacons again offer five colours and additionally three user selectable modes of operation steady single flash and double flash.LED beacons also are inherently robust and have extremely long operating lifetimes important where access for maintenance may be limited. Supply voltages from 9 to 60Vdc and 110 to 230Vac are available.Please see data sheets for the particular devices for full specification.Key Features Two three or four way assemblies to suit the status levels required.Two stage alarm sounders with 32 tones avoids conflicts with other alarm signalsFive colours available with both Xenon and LED light sources to suit most visual requirementsChoice of three light outputs for the Xenon beacons to suit the visibility levels requiredThree user selectable flash modes from the LED beacons allows clear differentiation between signals.Audible and visual elements can be locked into the Combi bases for added securityBases are available in either red or white to suit the applicationStandard voltage range 9 to 30Vdc. 60Vdc also available and will suit most commonly available DC suppliesAC mains operation from 110 to 230Vac with Combi Power module allows operation from AC supplies with the need for adjustment.

GBP 5.40
1